Merge branch 'matrix-clear'
[tmk_keyboard.git] / converter / x68k_usb / Makefile
CommitLineData
38d61ee1 1#
2# Makefile for PJRC Teensy
3#
4
5
6# Target file name (without extension).
e3994a62 7TARGET = x68k_usb
38d61ee1 8
9# Directory common source filess exist
7860d099 10TMK_DIR = ../../tmk_core
38d61ee1 11
12# Directory keyboard dependent files exist
13TARGET_DIR = .
14
15# keyboard dependent files
2769f09d 16SRC = keymap.c \
38d61ee1 17 matrix.c \
18 led.c \
f45f4193 19 protocol/serial_uart.c
38d61ee1 20
e7808f7e 21CONFIG_H = config.h
38d61ee1 22
23
24# MCU name, you MUST set this to match the board you are using
25# type "make clean" after changing this, so all files will be rebuilt
26#MCU = at90usb162 # Teensy 1.0
e3994a62 27#MCU = atmega32u4 # Teensy 2.0
38d61ee1 28#MCU = at90usb646 # Teensy++ 1.0
29#MCU = at90usb1286 # Teensy++ 2.0
e3994a62 30MCU = atmega32u2 # Teensy 2.0
38d61ee1 31
32
33# Processor frequency.
34# Normally the first thing your program should do is set the clock prescaler,
35# so your program will run at the correct speed. You should also set this
36# variable to same clock speed. The _delay_ms() macro uses this, and many
37# examples use this variable to calculate timings. Do not add a "UL" here.
38F_CPU = 16000000
39
40
e3994a62 41#
42# LUFA specific
43#
44# Target architecture (see library "Board Types" documentation).
45ARCH = AVR8
46
47# Input clock frequency.
48# This will define a symbol, F_USB, in all source code files equal to the
49# input clock frequency (before any prescaling is performed) in Hz. This value may
50# differ from F_CPU if prescaling is used on the latter, and is required as the
51# raw input clock is fed directly to the PLL sections of the AVR for high speed
52# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
53# at the end, this will be done automatically to create a 32-bit value in your
54# source code.
55#
56# If no clock division is performed on the input clock inside the AVR (via the
57# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
58F_USB = $(F_CPU)
59
60# Interrupt driven control endpoint task(+60)
61#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
62
63
42c96241 64# Boot Section Size in bytes
65# Teensy halfKay 512
66# Atmel DFU loader 4096
67# LUFA bootloader 4096
68OPT_DEFS += -DBOOTLOADER_SIZE=4096
69
70
38d61ee1 71# Build Options
72# *Comment out* to disable the options.
73#
42c96241 74BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
75MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
76EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
77CONSOLE_ENABLE = yes # Console for debug(+400)
78COMMAND_ENABLE = yes # Commands for debug and configuration
79#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
80#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
38d61ee1 81
82
83
84#---------------- Programming Options --------------------------
85AVRDUDE = avrdude
86# Type: avrdude -c ? to get a full listing.
87AVRDUDE_PROGRAMMER = avr109
88AVRDUDE_PORT = /dev/ttyACM0
89AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
90#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
91
92# Uncomment the following if you want avrdude's erase cycle counter.
93# Note that this counter needs to be initialized first using -Yn,
94# see avrdude manual.
95#AVRDUDE_ERASE_COUNTER = -y
96
97# Uncomment the following if you do /not/ wish a verification to be
98# performed after programming the device.
99#AVRDUDE_NO_VERIFY = -V
100
101# Increase verbosity level. Please use this when submitting bug
102# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
103# to submit bug reports.
104#AVRDUDE_VERBOSE = -v -v
105
106AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
107#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
108AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
109AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
110AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
111
e3994a62 112PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
38d61ee1 113
114
2769f09d 115# Search Path
116VPATH += $(TARGET_DIR)
b4e2d325 117VPATH += $(TMK_DIR)
2769f09d 118
38d61ee1 119
b4e2d325 120include $(TMK_DIR)/protocol.mk
e3994a62 121include $(TMK_DIR)/protocol/lufa.mk
b4e2d325 122include $(TMK_DIR)/common.mk
123include $(TMK_DIR)/rules.mk
Imprint / Impressum