pana_m8: Add initial files
[tmk_keyboard.git] / converter / sun_usb / Makefile
CommitLineData
97ee1be5 1# Target file name (without extension).
2TARGET = sun_usb
3
4# Directory common source filess exist
7860d099 5TMK_DIR = ../../tmk_core
97ee1be5 6
7# Directory keyboard dependent files exist
8TARGET_DIR = .
9
10# keyboard dependent files
11SRC = keymap.c \
12 matrix.c \
13 led.c \
d3332d32
JH
14 command_extra.c
15
97ee1be5 16
17CONFIG_H = config.h
18
19
20# MCU name, you MUST set this to match the board you are using
21# type "make clean" after changing this, so all files will be rebuilt
22#MCU = at90usb162 # Teensy 1.0
62117e7e 23#MCU = atmega32u4 # Teensy 2.0
97ee1be5 24#MCU = at90usb646 # Teensy++ 1.0
25#MCU = at90usb1286 # Teensy++ 2.0
62117e7e 26MCU = atmega32u2
97ee1be5 27
28
29# Processor frequency.
30# Normally the first thing your program should do is set the clock prescaler,
31# so your program will run at the correct speed. You should also set this
32# variable to same clock speed. The _delay_ms() macro uses this, and many
33# examples use this variable to calculate timings. Do not add a "UL" here.
34F_CPU = 16000000
35
36
b56717b8 37#
38# LUFA specific
39#
40# Target architecture (see library "Board Types" documentation).
41ARCH = AVR8
42
43# Input clock frequency.
44# This will define a symbol, F_USB, in all source code files equal to the
45# input clock frequency (before any prescaling is performed) in Hz. This value may
46# differ from F_CPU if prescaling is used on the latter, and is required as the
47# raw input clock is fed directly to the PLL sections of the AVR for high speed
48# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
49# at the end, this will be done automatically to create a 32-bit value in your
50# source code.
51#
52# If no clock division is performed on the input clock inside the AVR (via the
53# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
54F_USB = $(F_CPU)
55
56# Interrupt driven control endpoint task
57OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
58
59
97ee1be5 60# Build Options
61# *Comment out* to disable the options.
62#
63MOUSEKEY_ENABLE = yes # Mouse keys
64EXTRAKEY_ENABLE = yes # Audio control and System control
b56717b8 65CONSOLE_ENABLE = yes # Console for debug
523cc6aa 66COMMAND_ENABLE = yes # Commands for debug and configuration
d3332d32 67#HARDWARE_SERIAL = yes # Use hardware serial (requires inverted serial, see README)
b56717b8 68#NKRO_ENABLE = yes # USB Nkey Rollover
97ee1be5 69
d3332d32
JH
70ifdef HARDWARE_SERIAL
71 SRC := protocol/serial_uart.c $(SRC)
72 OPT_DEFS += -DHARDWARE_SERIAL
73else
74 SRC := protocol/serial_soft.c $(SRC)
75endif
97ee1be5 76
b56717b8 77# Boot Section Size in bytes
78# Teensy halfKay 512
79# Atmel DFU loader 4096
80# LUFA bootloader 4096
353a9b56 81OPT_DEFS += -DBOOTLOADER_SIZE=4096
97ee1be5 82
83
84# Search Path
85VPATH += $(TARGET_DIR)
b4e2d325 86VPATH += $(TMK_DIR)
97ee1be5 87
88
b4e2d325 89include $(TMK_DIR)/protocol/lufa.mk
90include $(TMK_DIR)/protocol.mk
91include $(TMK_DIR)/common.mk
92include $(TMK_DIR)/rules.mk
Imprint / Impressum