Fix Makefile for NKRO comment
[tmk_keyboard.git] / keyboard / onekey / Makefile
CommitLineData
b6677f10 1#----------------------------------------------------------------------------
2# On command line:
3#
4# make all = Make software.
5#
6# make clean = Clean out built project files.
7#
8# make coff = Convert ELF to AVR COFF.
9#
10# make extcoff = Convert ELF to AVR Extended COFF.
11#
12# make program = Download the hex file to the device.
13# Please customize your programmer settings(PROGRAM_CMD)
14#
15# make teensy = Download the hex file to the device, using teensy_loader_cli.
16# (must have teensy_loader_cli installed).
17#
18# make dfu = Download the hex file to the device, using dfu-programmer (must
19# have dfu-programmer installed).
20#
21# make flip = Download the hex file to the device, using Atmel FLIP (must
22# have Atmel FLIP installed).
23#
24# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25# (must have dfu-programmer installed).
26#
27# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28# (must have Atmel FLIP installed).
29#
30# make debug = Start either simulavr or avarice as specified for debugging,
31# with avr-gdb or avr-insight as the front end for debugging.
32#
33# make filename.s = Just compile filename.c into the assembler code only.
34#
35# make filename.i = Create a preprocessed source file for use in submitting
36# bug reports to the GCC project.
37#
38# To rebuild project do "make clean" then "make all".
39#----------------------------------------------------------------------------
40
41# Target file name (without extension).
42TARGET = onekey_lufa
43
44# Directory common source filess exist
7860d099 45TMK_DIR = ../../tmk_core
b6677f10 46
47# Directory keyboard dependent files exist
48TARGET_DIR = .
49
50# project specific files
51SRC = keymap.c \
52 matrix.c \
53 led.c
54
55CONFIG_H = config.h
56
57
58# MCU name
59#MCU = at90usb1287
60MCU = atmega32u4
61
62# Processor frequency.
63# This will define a symbol, F_CPU, in all source code files equal to the
64# processor frequency in Hz. You can then use this symbol in your source code to
65# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
66# automatically to create a 32-bit value in your source code.
67#
68# This will be an integer division of F_USB below, as it is sourced by
69# F_USB after it has run through any CPU prescalers. Note that this value
70# does not *change* the processor frequency - it should merely be updated to
71# reflect the processor speed set externally so that the code can use accurate
72# software delays.
73F_CPU = 16000000
74
75
76#
77# LUFA specific
78#
79# Target architecture (see library "Board Types" documentation).
80ARCH = AVR8
81
82# Input clock frequency.
83# This will define a symbol, F_USB, in all source code files equal to the
84# input clock frequency (before any prescaling is performed) in Hz. This value may
85# differ from F_CPU if prescaling is used on the latter, and is required as the
86# raw input clock is fed directly to the PLL sections of the AVR for high speed
87# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
88# at the end, this will be done automatically to create a 32-bit value in your
89# source code.
90#
91# If no clock division is performed on the input clock inside the AVR (via the
92# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
93F_USB = $(F_CPU)
94
95# Interrupt driven control endpoint task(+60)
a9c3f475 96OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
b6677f10 97
98
99# Boot Section Size in *bytes*
100# Teensy halfKay 512
101# Teensy++ halfKay 1024
102# Atmel DFU loader 4096
103# LUFA bootloader 4096
104# USBaspLoader 2048
105OPT_DEFS += -DBOOTLOADER_SIZE=4096
106
107
108# Build Options
109# comment out to disable the options.
110#
755e4d8b 111#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
112#MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
113#EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
b6677f10 114CONSOLE_ENABLE = yes # Console for debug(+400)
755e4d8b 115#COMMAND_ENABLE = yes # Commands for debug and configuration
116#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
8b509aa1 117#NKRO_ENABLE = yes # USB Nkey Rollover
b6677f10 118
05be3d85 119#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support
120#PS2_USE_BUSYWAIT = yes # uses primitive reference code
755e4d8b 121#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
122#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
b6677f10 123
b6677f10 124
125# Search Path
126VPATH += $(TARGET_DIR)
b4e2d325 127VPATH += $(TMK_DIR)
b6677f10 128
b4e2d325 129include $(TMK_DIR)/common.mk
130include $(TMK_DIR)/protocol.mk
131include $(TMK_DIR)/protocol/lufa.mk
132include $(TMK_DIR)/rules.mk
Imprint / Impressum