Fix: Use action_t in keymap files
[tmk_keyboard.git] / orphan / ghost_squid / Makefile.lufa
CommitLineData
a6d33e2c
VO
1#----------------------------------------------------------------------------
2# On command line:
3#
4# make all = Make software.
5#
6# make clean = Clean out built project files.
7#
8# make coff = Convert ELF to AVR COFF.
9#
10# make extcoff = Convert ELF to AVR Extended COFF.
11#
12# make program = Download the hex file to the device.
13# Please customize your programmer settings(PROGRAM_CMD)
14#
15# make teensy = Download the hex file to the device, using teensy_loader_cli.
16# (must have teensy_loader_cli installed).
17#
18# make dfu = Download the hex file to the device, using dfu-programmer (must
19# have dfu-programmer installed).
20#
21# make flip = Download the hex file to the device, using Atmel FLIP (must
22# have Atmel FLIP installed).
23#
24# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25# (must have dfu-programmer installed).
26#
27# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28# (must have Atmel FLIP installed).
29#
30# make debug = Start either simulavr or avarice as specified for debugging,
31# with avr-gdb or avr-insight as the front end for debugging.
32#
33# make filename.s = Just compile filename.c into the assembler code only.
34#
35# make filename.i = Create a preprocessed source file for use in submitting
36# bug reports to the GCC project.
37#
38# To rebuild project do "make clean" then "make all".
39#----------------------------------------------------------------------------
40
41# Target file name (without extension).
42TARGET = ghostsquid_lufa
43
44# Directory common source filess exist
7860d099 45TMK_DIR = ../../tmk_core
a6d33e2c
VO
46
47# Directory keyboard dependent files exist
48TARGET_DIR = .
49
50# List C source files here. (C dependencies are automatically generated.)
51SRC = keymap.c \
52 matrix.c \
53 led.c
54
55CONFIG_H = config.h
56
57# MCU name
58MCU = atmega32u2
59
60# Processor frequency.
61# This will define a symbol, F_CPU, in all source code files equal to the
62# processor frequency in Hz. You can then use this symbol in your source code to
63# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
64# automatically to create a 32-bit value in your source code.
65#
66# This will be an integer division of F_USB below, as it is sourced by
67# F_USB after it has run through any CPU prescalers. Note that this value
68# does not *change* the processor frequency - it should merely be updated to
69# reflect the processor speed set externally so that the code can use accurate
70# software delays.
71F_CPU = 16000000
72
73#
74# LUFA specific
75#
76# Target architecture (see library "Board Types" documentation).
77ARCH = AVR8
78
79# Input clock frequency.
80# This will define a symbol, F_USB, in all source code files equal to the
81# input clock frequency (before any prescaling is performed) in Hz. This value may
82# differ from F_CPU if prescaling is used on the latter, and is required as the
83# raw input clock is fed directly to the PLL sections of the AVR for high speed
84# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
85# at the end, this will be done automatically to create a 32-bit value in your
86# source code.
87#
88# If no clock division is performed on the input clock inside the AVR (via the
89# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
90F_USB = $(F_CPU)
91
92
93# Build Options
94# comment out to disable the options.
95#
96#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
97MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
98EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
99#CONSOLE_ENABLE = yes # Console for debug(+400)
100COMMAND_ENABLE = yes # Commands for debug and configuration
101#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
102#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
103
104
105# Boot Section Size in bytes
106# Teensy halfKay 512
107# Atmel DFU loader 4096
108# LUFA bootloader 4096
109OPT_DEFS += -DBOOTLOADER_SIZE=4096
110
111# Search Path
112VPATH += $(TARGET_DIR)
b4e2d325 113VPATH += $(TMK_DIR)
a6d33e2c 114
b4e2d325 115include $(TMK_DIR)/protocol/lufa.mk
116include $(TMK_DIR)/common.mk
117include $(TMK_DIR)/rules.mk
Imprint / Impressum