Make ps2_usart default and fix SpaceFN
[tmk_keyboard.git] / converter / ps2_usb / Makefile
CommitLineData
bf1a37ba 1# Target file name (without extension).
04c95015 2TARGET = ps2_usb_lufa
bf1a37ba 3
4# Directory common source filess exist
afb08462 5TOP_DIR = ../..
bf1a37ba 6
7# Directory keyboard dependent files exist
8TARGET_DIR = .
9
04c95015 10# project specific files
11SRC = keymap_common.c \
12 matrix.c \
13 led.c
14
15ifdef KEYMAP
16 SRC := keymap_$(KEYMAP).c $(SRC)
17else
18 SRC := keymap_plain.c $(SRC)
19endif
20
21CONFIG_H = config.h
bf1a37ba 22
bf1a37ba 23
04c95015 24# MCU name
25#MCU = at90usb1287
26MCU = atmega32u4
bf1a37ba 27
28# Processor frequency.
04c95015 29# This will define a symbol, F_CPU, in all source code files equal to the
30# processor frequency in Hz. You can then use this symbol in your source code to
31# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
32# automatically to create a 32-bit value in your source code.
33#
34# This will be an integer division of F_USB below, as it is sourced by
35# F_USB after it has run through any CPU prescalers. Note that this value
36# does not *change* the processor frequency - it should merely be updated to
37# reflect the processor speed set externally so that the code can use accurate
38# software delays.
bf1a37ba 39F_CPU = 16000000
40
41
bf1a37ba 42#
04c95015 43# LUFA specific
44#
45# Target architecture (see library "Board Types" documentation).
46ARCH = AVR8
47
48# Input clock frequency.
49# This will define a symbol, F_USB, in all source code files equal to the
50# input clock frequency (before any prescaling is performed) in Hz. This value may
51# differ from F_CPU if prescaling is used on the latter, and is required as the
52# raw input clock is fed directly to the PLL sections of the AVR for high speed
53# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
54# at the end, this will be done automatically to create a 32-bit value in your
55# source code.
56#
57# If no clock division is performed on the input clock inside the AVR (via the
58# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
59F_USB = $(F_CPU)
bf1a37ba 60
04c95015 61# Interrupt driven control endpoint task(+60)
62OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
1ac674db 63
64
04c95015 65# Boot Section Size in *bytes*
66# Teensy halfKay 512
67# Teensy++ halfKay 1024
68# Atmel DFU loader 4096
69# LUFA bootloader 4096
70# USBaspLoader 2048
71OPT_DEFS += -DBOOTLOADER_SIZE=4096
1ac674db 72
1ac674db 73
04c95015 74# Build Options
75# comment out to disable the options.
76#
77#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
78MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
79EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
80CONSOLE_ENABLE = yes # Console for debug(+400)
81COMMAND_ENABLE = yes # Commands for debug and configuration
82NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
1ac674db 83
bf1a37ba 84
04c95015 85# PS/2 Options
86#
c9dee36e 87PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
04c95015 88#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
c9dee36e 89#PS2_USE_BUSYWAIT = yes # uses primitive reference code
fb8d23c6 90
fb8d23c6 91
04c95015 92# Optimize size but this may cause error "relocation truncated to fit"
93#EXTRALDFLAGS = -Wl,--relax
fb8d23c6 94
2769f09d 95# Search Path
96VPATH += $(TARGET_DIR)
97VPATH += $(TOP_DIR)
98
63d82fca 99include $(TOP_DIR)/protocol.mk
04c95015 100include $(TOP_DIR)/protocol/lufa.mk
63d82fca 101include $(TOP_DIR)/common.mk
102include $(TOP_DIR)/rules.mk
Imprint / Impressum