]>
Commit | Line | Data |
---|---|---|
1 | # Target file name (without extension). | |
2 | TARGET ?= ps2_usb | |
3 | ||
4 | # Directory common source filess exist | |
5 | TMK_DIR ?= ../../tmk_core | |
6 | ||
7 | # Directory keyboard dependent files exist | |
8 | TARGET_DIR ?= . | |
9 | ||
10 | # project specific files | |
11 | SRC ?= matrix.c \ | |
12 | led.c | |
13 | ||
14 | # | |
15 | # Keymap file | |
16 | # | |
17 | ifdef UNIMAP_ENABLE | |
18 | KEYMAP_FILE = unimap | |
19 | else | |
20 | ifdef ACTIONMAP_ENABLE | |
21 | KEYMAP_FILE = actionmap | |
22 | else | |
23 | KEYMAP_FILE = keymap | |
24 | endif | |
25 | endif | |
26 | ifdef KEYMAP | |
27 | SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) | |
28 | else | |
29 | SRC := $(KEYMAP_FILE)_plain.c $(SRC) | |
30 | endif | |
31 | ||
32 | CONFIG_H ?= config.h | |
33 | ||
34 | ||
35 | # MCU name | |
36 | MCU ?= atmega32u2 | |
37 | ||
38 | # Processor frequency. | |
39 | # This will define a symbol, F_CPU, in all source code files equal to the | |
40 | # processor frequency in Hz. You can then use this symbol in your source code to | |
41 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
42 | # automatically to create a 32-bit value in your source code. | |
43 | # | |
44 | # This will be an integer division of F_USB below, as it is sourced by | |
45 | # F_USB after it has run through any CPU prescalers. Note that this value | |
46 | # does not *change* the processor frequency - it should merely be updated to | |
47 | # reflect the processor speed set externally so that the code can use accurate | |
48 | # software delays. | |
49 | F_CPU ?= 16000000 | |
50 | ||
51 | ||
52 | # | |
53 | # LUFA specific | |
54 | # | |
55 | # Target architecture (see library "Board Types" documentation). | |
56 | ARCH ?= AVR8 | |
57 | ||
58 | # Input clock frequency. | |
59 | # This will define a symbol, F_USB, in all source code files equal to the | |
60 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
61 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
62 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
63 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
64 | # at the end, this will be done automatically to create a 32-bit value in your | |
65 | # source code. | |
66 | # | |
67 | # If no clock division is performed on the input clock inside the AVR (via the | |
68 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
69 | F_USB ?= $(F_CPU) | |
70 | ||
71 | # Interrupt driven control endpoint task | |
72 | # Not work with suart debug | |
73 | #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
74 | ||
75 | # This improves response of keyboard when wakeup | |
76 | OPT_DEFS += -DSUSPEND_MODE_STANDBY | |
77 | ||
78 | # Boot Section Size in *bytes* | |
79 | # Teensy halfKay 512 | |
80 | # Teensy++ halfKay 1024 | |
81 | # Atmel DFU loader 4096 | |
82 | # LUFA bootloader 4096 | |
83 | # USBaspLoader 2048 | |
84 | BOOTLOADER_SIZE ?= 4096 | |
85 | OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE) | |
86 | ||
87 | ||
88 | # Build Options | |
89 | # comment out to disable the options. | |
90 | # | |
91 | BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |
92 | MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |
93 | EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |
94 | CONSOLE_ENABLE ?= yes # Console for debug(+400) | |
95 | COMMAND_ENABLE ?= yes # Commands for debug and configuration | |
96 | NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |
97 | ||
98 | ||
99 | # PS/2 Options | |
100 | # | |
101 | #PS2_USE_USART ?= yes # uses hardware USART engine for PS/2 signal receive(recomened) | |
102 | PS2_USE_INT ?= yes # uses external interrupt for falling edge of PS/2 clock pin | |
103 | #PS2_USE_BUSYWAIT ?= yes # uses primitive reference code | |
104 | ||
105 | ||
106 | # Optimize size but this may cause error "relocation truncated to fit" | |
107 | #EXTRALDFLAGS = -Wl,--relax | |
108 | ||
109 | # Search Path | |
110 | VPATH += $(TARGET_DIR) | |
111 | VPATH += $(TMK_DIR) | |
112 | ||
113 | include $(TMK_DIR)/protocol.mk | |
114 | include $(TMK_DIR)/protocol/lufa.mk | |
115 | include $(TMK_DIR)/common.mk | |
116 | include $(TMK_DIR)/rules.mk |