git.gir.st - tmk_keyboard.git/blame_incremental

... / ...

Commit	Line	Data
	1	#
	2	# Makefile for PJRC Teensy
	3	#
	4
	5
	6	# Target file name (without extension).
	7	TARGET = x68k_usb_pjrc
	8
	9	# Directory common source filess exist
	10	TOP_DIR = ../..
	11
	12	# Directory keyboard dependent files exist
	13	TARGET_DIR = .
	14
	15	# keyboard dependent files
	16	SRC = keymap.c \
	17	matrix.c \
	18	led.c \
	19	protocol/serial_uart.c
	20
	21	CONFIG_H = config_pjrc.h
	22
	23
	24	# MCU name, you MUST set this to match the board you are using
	25	# type "make clean" after changing this, so all files will be rebuilt
	26	#MCU = at90usb162 # Teensy 1.0
	27	MCU = atmega32u4 # Teensy 2.0
	28	#MCU = at90usb646 # Teensy++ 1.0
	29	#MCU = at90usb1286 # Teensy++ 2.0
	30
	31
	32	# Processor frequency.
	33	# Normally the first thing your program should do is set the clock prescaler,
	34	# so your program will run at the correct speed. You should also set this
	35	# variable to same clock speed. The _delay_ms() macro uses this, and many
	36	# examples use this variable to calculate timings. Do not add a "UL" here.
	37	F_CPU = 16000000
	38
	39
	40	# Boot Section Size in bytes
	41	# Teensy halfKay 512
	42	# Atmel DFU loader 4096
	43	# LUFA bootloader 4096
	44	OPT_DEFS += -DBOOTLOADER_SIZE=4096
	45
	46
	47	# Build Options
	48	# Comment out to disable the options.
	49	#
	50	BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
	51	MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
	52	EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
	53	CONSOLE_ENABLE = yes # Console for debug(+400)
	54	COMMAND_ENABLE = yes # Commands for debug and configuration
	55	#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
	56	#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
	57
	58
	59
	60	#---------------- Programming Options --------------------------
	61	AVRDUDE = avrdude
	62	# Type: avrdude -c ? to get a full listing.
	63	AVRDUDE_PROGRAMMER = avr109
	64	AVRDUDE_PORT = /dev/ttyACM0
	65	AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
	66	#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
	67
	68	# Uncomment the following if you want avrdude's erase cycle counter.
	69	# Note that this counter needs to be initialized first using -Yn,
	70	# see avrdude manual.
	71	#AVRDUDE_ERASE_COUNTER = -y
	72
	73	# Uncomment the following if you do /not/ wish a verification to be
	74	# performed after programming the device.
	75	#AVRDUDE_NO_VERIFY = -V
	76
	77	# Increase verbosity level. Please use this when submitting bug
	78	# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
	79	# to submit bug reports.
	80	#AVRDUDE_VERBOSE = -v -v
	81
	82	AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
	83	#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
	84	AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
	85	AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
	86	AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
	87
	88	#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
	89	#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
	90	PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
	91
	92
	93	# Search Path
	94	VPATH += $(TARGET_DIR)
	95	VPATH += $(TOP_DIR)
	96
	97
	98	include $(TOP_DIR)/protocol/pjrc.mk
	99	include $(TOP_DIR)/protocol.mk
	100	include $(TOP_DIR)/common.mk
	101	include $(TOP_DIR)/rules.mk