]>
Commit | Line | Data |
---|---|---|
1 | # | |
2 | # Makefile for V-USB | |
3 | # | |
4 | ||
5 | ||
6 | # Target file name (without extension). | |
7 | TARGET = ps2_usb_vusb | |
8 | ||
9 | # Directory common source filess exist | |
10 | TOP_DIR = ../.. | |
11 | ||
12 | # Directory keyboard dependent files exist | |
13 | TARGET_DIR = . | |
14 | ||
15 | # keyboard dependent files | |
16 | SRC = keymap.c \ | |
17 | matrix.c \ | |
18 | led.c \ | |
19 | ps2_usart.c | |
20 | ||
21 | CONFIG_H = config_vusb.h | |
22 | ||
23 | ||
24 | # V-USB debug level: To use ps2_usart.c level must be 0 | |
25 | # ps2_usart.c requires USART to receive PS/2 signal. | |
26 | OPT_DEFS = -DDEBUG_LEVEL=0 | |
27 | ||
28 | ||
29 | # MCU name, you MUST set this to match the board you are using | |
30 | # type "make clean" after changing this, so all files will be rebuilt | |
31 | #MCU = at90usb162 # Teensy 1.0 | |
32 | #MCU = atmega32u4 # Teensy 2.0 | |
33 | #MCU = at90usb646 # Teensy++ 1.0 | |
34 | #MCU = at90usb1286 # Teensy++ 2.0 | |
35 | MCU = atmega168 | |
36 | ||
37 | ||
38 | # Processor frequency. | |
39 | # Normally the first thing your program should do is set the clock prescaler, | |
40 | # so your program will run at the correct speed. You should also set this | |
41 | # variable to same clock speed. The _delay_ms() macro uses this, and many | |
42 | # examples use this variable to calculate timings. Do not add a "UL" here. | |
43 | F_CPU = 20000000 | |
44 | ||
45 | ||
46 | # Build Options | |
47 | # comment out to disable the options. | |
48 | # | |
49 | MOUSEKEY_ENABLE = yes # Mouse keys | |
50 | EXTRAKEY_ENABLE = yes # Audio control and System control | |
51 | #NKRO_ENABLE = yes # USB Nkey Rollover | |
52 | NO_UART = yes # UART is unavailable | |
53 | ||
54 | ||
55 | ||
56 | #---------------- Programming Options -------------------------- | |
57 | AVRDUDE = avrdude | |
58 | # Type: avrdude -c ? to get a full listing. | |
59 | AVRDUDE_PROGRAMMER = usbasp | |
60 | AVRDUDE_PORT = | |
61 | AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex | |
62 | #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep | |
63 | ||
64 | # Uncomment the following if you want avrdude's erase cycle counter. | |
65 | # Note that this counter needs to be initialized first using -Yn, | |
66 | # see avrdude manual. | |
67 | #AVRDUDE_ERASE_COUNTER = -y | |
68 | ||
69 | # Uncomment the following if you do /not/ wish a verification to be | |
70 | # performed after programming the device. | |
71 | #AVRDUDE_NO_VERIFY = -V | |
72 | ||
73 | # Increase verbosity level. Please use this when submitting bug | |
74 | # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> | |
75 | # to submit bug reports. | |
76 | #AVRDUDE_VERBOSE = -v -v | |
77 | ||
78 | #AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) | |
79 | AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) | |
80 | AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) | |
81 | AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) | |
82 | AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) | |
83 | ||
84 | PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) | |
85 | ||
86 | ||
87 | # Boot Section Size in bytes | |
88 | # Teensy halfKay 512 | |
89 | # Atmel DFU loader 4096 | |
90 | # LUFA bootloader 4096 | |
91 | # USBasp 2048 | |
92 | OPT_DEFS += -DBOOT_SIZE=2048 | |
93 | ||
94 | ||
95 | # Search Path | |
96 | VPATH += $(TARGET_DIR) | |
97 | VPATH += $(TOP_DIR) | |
98 | ||
99 | ||
100 | include $(TOP_DIR)/protocol/vusb.mk | |
101 | include $(TOP_DIR)/protocol.mk | |
102 | include $(TOP_DIR)/common.mk | |
103 | include $(TOP_DIR)/rules.mk |