]>
Commit | Line | Data |
---|---|---|
1 | # Target name | |
2 | TARGET ?= fc660c | |
3 | ||
4 | # Location of tmk_core | |
5 | TMK_DIR ?= ../../tmk_core | |
6 | ||
7 | # Location of target dependent files exist | |
8 | TARGET_DIR ?= . | |
9 | ||
10 | ||
11 | # List C source files | |
12 | SRC ?= fc660c.c | |
13 | ||
14 | # Configure file | |
15 | CONFIG_H ?= config.h | |
16 | ||
17 | ||
18 | # MCU name | |
19 | MCU ?= atmega32u4 | |
20 | ||
21 | # Processor frequency. | |
22 | # This will define a symbol, F_CPU, in all source code files equal to the | |
23 | # processor frequency in Hz. You can then use this symbol in your source code to | |
24 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
25 | # automatically to create a 32-bit value in your source code. | |
26 | # | |
27 | # This will be an integer division of F_USB below, as it is sourced by | |
28 | # F_USB after it has run through any CPU prescalers. Note that this value | |
29 | # does not *change* the processor frequency - it should merely be updated to | |
30 | # reflect the processor speed set externally so that the code can use accurate | |
31 | # software delays. | |
32 | F_CPU ?= 16000000 | |
33 | ||
34 | ||
35 | # | |
36 | # LUFA specific | |
37 | # | |
38 | # Target architecture (see library "Board Types" documentation). | |
39 | ARCH ?= AVR8 | |
40 | ||
41 | # Input clock frequency. | |
42 | # This will define a symbol, F_USB, in all source code files equal to the | |
43 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
44 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
45 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
46 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
47 | # at the end, this will be done automatically to create a 32-bit value in your | |
48 | # source code. | |
49 | # | |
50 | # If no clock division is performed on the input clock inside the AVR (via the | |
51 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
52 | F_USB ?= $(F_CPU) | |
53 | ||
54 | # Interrupt driven control endpoint task | |
55 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
56 | ||
57 | ||
58 | # Boot Section Size in *bytes* | |
59 | # Teensy halfKay 512 | |
60 | # Teensy++ halfKay 1024 | |
61 | # Atmel DFU loader 4096 (TMK Alt Controller) | |
62 | # LUFA bootloader 4096 | |
63 | # USBaspLoader 2048 | |
64 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
65 | ||
66 | ||
67 | # Build Options | |
68 | # comment out to disable the options. | |
69 | # | |
70 | #BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration | |
71 | MOUSEKEY_ENABLE ?= yes # Mouse keys | |
72 | EXTRAKEY_ENABLE ?= yes # Audio control and System control | |
73 | CONSOLE_ENABLE ?= yes # Console for debug | |
74 | COMMAND_ENABLE ?= yes # Commands for debug and configuration | |
75 | NKRO_ENABLE ?= yes # USB Nkey Rollover | |
76 | #UNIMAP_ENABLE ?= yes # Universal keymap | |
77 | ACTIONMAP_ENABLE ?= yes # Use 16bit actionmap instead of 8bit keymap | |
78 | #KEYMAP_SECTION_ENABLE ?= yes # fixed address keymap for keymap editor | |
79 | ||
80 | #OPT_DEFS += -DNO_ACTION_TAPPING | |
81 | #OPT_DEFS += -DNO_ACTION_LAYER | |
82 | #OPT_DEFS += -DNO_ACTION_MACRO | |
83 | ||
84 | ||
85 | # | |
86 | # Keymap file | |
87 | # | |
88 | ifeq (yes,$(strip $(UNIMAP_ENABLE))) | |
89 | KEYMAP_FILE = unimap | |
90 | else | |
91 | ifeq (yes,$(strip $(ACTIONMAP_ENABLE))) | |
92 | KEYMAP_FILE = actionmap | |
93 | else | |
94 | KEYMAP_FILE = keymap | |
95 | endif | |
96 | endif | |
97 | ifdef KEYMAP | |
98 | SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) | |
99 | else | |
100 | SRC := $(KEYMAP_FILE).c $(SRC) | |
101 | endif | |
102 | ||
103 | ||
104 | # Search Path | |
105 | VPATH += $(TARGET_DIR) | |
106 | VPATH += $(TMK_DIR) | |
107 | ||
108 | include $(TMK_DIR)/protocol/lufa.mk | |
109 | include $(TMK_DIR)/common.mk | |
110 | include $(TMK_DIR)/rules.mk |