| | 1 | # |
| | 2 | # Makefile for PJRC Teensy |
| | 3 | # |
| | 4 | |
| | 5 | |
| | 6 | # Target file name (without extension). |
| | 7 | TARGET = x68k_usb_pjrc |
| | 8 | |
| | 9 | # Directory common source filess exist |
| | 10 | TOP_DIR = ../.. |
| | 11 | |
| | 12 | # Directory keyboard dependent files exist |
| | 13 | TARGET_DIR = . |
| | 14 | |
| | 15 | # keyboard dependent files |
| | 16 | SRC = main.c \ |
| | 17 | keymap.c \ |
| | 18 | matrix.c \ |
| | 19 | led.c \ |
| | 20 | x68k.c |
| | 21 | |
| | 22 | CONFIG_H = config_pjrc.h |
| | 23 | |
| | 24 | |
| | 25 | # MCU name, you MUST set this to match the board you are using |
| | 26 | # type "make clean" after changing this, so all files will be rebuilt |
| | 27 | #MCU = at90usb162 # Teensy 1.0 |
| | 28 | MCU = atmega32u4 # Teensy 2.0 |
| | 29 | #MCU = at90usb646 # Teensy++ 1.0 |
| | 30 | #MCU = at90usb1286 # Teensy++ 2.0 |
| | 31 | |
| | 32 | |
| | 33 | # Processor frequency. |
| | 34 | # Normally the first thing your program should do is set the clock prescaler, |
| | 35 | # so your program will run at the correct speed. You should also set this |
| | 36 | # variable to same clock speed. The _delay_ms() macro uses this, and many |
| | 37 | # examples use this variable to calculate timings. Do not add a "UL" here. |
| | 38 | F_CPU = 16000000 |
| | 39 | |
| | 40 | |
| | 41 | # Build Options |
| | 42 | # *Comment out* to disable the options. |
| | 43 | # |
| | 44 | MOUSEKEY_ENABLE = yes # Mouse keys |
| | 45 | EXTRAKEY_ENABLE = yes # Audio control and System control |
| | 46 | NKRO_ENABLE = yes # USB Nkey Rollover |
| | 47 | |
| | 48 | |
| | 49 | |
| | 50 | #---------------- Programming Options -------------------------- |
| | 51 | AVRDUDE = avrdude |
| | 52 | # Type: avrdude -c ? to get a full listing. |
| | 53 | AVRDUDE_PROGRAMMER = avr109 |
| | 54 | AVRDUDE_PORT = /dev/ttyACM0 |
| | 55 | AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex |
| | 56 | #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep |
| | 57 | |
| | 58 | # Uncomment the following if you want avrdude's erase cycle counter. |
| | 59 | # Note that this counter needs to be initialized first using -Yn, |
| | 60 | # see avrdude manual. |
| | 61 | #AVRDUDE_ERASE_COUNTER = -y |
| | 62 | |
| | 63 | # Uncomment the following if you do /not/ wish a verification to be |
| | 64 | # performed after programming the device. |
| | 65 | #AVRDUDE_NO_VERIFY = -V |
| | 66 | |
| | 67 | # Increase verbosity level. Please use this when submitting bug |
| | 68 | # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> |
| | 69 | # to submit bug reports. |
| | 70 | #AVRDUDE_VERBOSE = -v -v |
| | 71 | |
| | 72 | AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) |
| | 73 | #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) |
| | 74 | AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) |
| | 75 | AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) |
| | 76 | AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) |
| | 77 | |
| | 78 | #PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) |
| | 79 | #PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex |
| | 80 | PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex |
| | 81 | |
| | 82 | |
| | 83 | |
| | 84 | include $(TOP_DIR)/protocol/pjrc.mk |
| | 85 | include $(TOP_DIR)/protocol.mk |
| | 86 | include $(TOP_DIR)/common.mk |
| | 87 | include $(TOP_DIR)/rules.mk |
git://git.gir.st / tmk_keyboard.git / blame_incremental