converter/xt_usb/Makefile

   1 #
   2 # Makefile for Teensy
   3 #
   4 # Target file name (without extension).
   5 TARGET = xt_usb_lufa
   6
   7 # Directory common source filess exist
   8 TMK_DIR = ../../tmk_core
   9
  10 # Directory keyboard dependent files exist
  11 TARGET_DIR = .
  12
  13 # project specific files
  14 SRC =   matrix.c \
  15         led.c
  16
  17 ifdef KEYMAP
  18     SRC := keymap_$(KEYMAP).c $(SRC)
  19 else
  20     SRC := keymap_plain.c $(SRC)
  21 endif
  22
  23 CONFIG_H = config.h
  24
  25
  26 # MCU name
  27 #MCU = at90usb1287
  28 MCU = atmega32u4
  29
  30 # Processor frequency.
  31 #     This will define a symbol, F_CPU, in all source code files equal to the
  32 #     processor frequency in Hz. You can then use this symbol in your source code to
  33 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  34 #     automatically to create a 32-bit value in your source code.
  35 #
  36 #     This will be an integer division of F_USB below, as it is sourced by
  37 #     F_USB after it has run through any CPU prescalers. Note that this value
  38 #     does not *change* the processor frequency - it should merely be updated to
  39 #     reflect the processor speed set externally so that the code can use accurate
  40 #     software delays.
  41 F_CPU = 16000000
  42
  43
  44 #
  45 # LUFA specific
  46 #
  47 # Target architecture (see library "Board Types" documentation).
  48 ARCH = AVR8
  49
  50 # Input clock frequency.
  51 #     This will define a symbol, F_USB, in all source code files equal to the
  52 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  53 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  54 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  55 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  56 #     at the end, this will be done automatically to create a 32-bit value in your
  57 #     source code.
  58 #
  59 #     If no clock division is performed on the input clock inside the AVR (via the
  60 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  61 F_USB = $(F_CPU)
  62
  63 # Interrupt driven control endpoint task(+60)
  64 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  65
  66
  67 # Boot Section Size in *bytes*
  68 #   Teensy halfKay   512
  69 #   Teensy++ halfKay 1024
  70 #   Atmel DFU loader 4096
  71 #   LUFA bootloader  4096
  72 #   USBaspLoader     2048
  73 OPT_DEFS += -DBOOTLOADER_SIZE=512
  74
  75
  76 # Build Options
  77 #   comment out to disable the options.
  78 #
  79 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  80 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  81 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  82 CONSOLE_ENABLE = yes    # Console for debug(+400)
  83 COMMAND_ENABLE = yes    # Commands for debug and configuration
  84 NKRO_ENABLE = yes       # USB Nkey Rollover - not yet supported in LUFA
  85
  86
  87 # XT/2 Options
  88 #
  89 XT_USE_INT = yes        # uses external interrupt for falling edge of PS/2 clock pin
  90
  91
  92 # Optimize size but this may cause error "relocation truncated to fit"
  93 #EXTRALDFLAGS = -Wl,--relax
  94
  95 # Search Path
  96 VPATH += $(TARGET_DIR)
  97 VPATH += $(TMK_DIR)
  98
  99 include $(TMK_DIR)/protocol.mk
 100 include $(TMK_DIR)/protocol/lufa.mk
 101 include $(TMK_DIR)/common.mk
 102 include $(TMK_DIR)/rules.mk