keyboard/alps64/Makefile

   1 # Target file name (without extension).
   2 TARGET ?= alps64
   3
   4 # Directory common source filess exist
   5 TMK_DIR ?= ../../tmk_core
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR ?= .
   9
  10 # project specific files
  11 SRC ?=  matrix.c \
  12         led.c
  13
  14 CONFIG_H ?= config.h
  15
  16
  17 # MCU name
  18 MCU ?= atmega32u2
  19
  20 # Processor frequency.
  21 #     This will define a symbol, F_CPU, in all source code files equal to the
  22 #     processor frequency in Hz. You can then use this symbol in your source code to
  23 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  24 #     automatically to create a 32-bit value in your source code.
  25 #
  26 #     This will be an integer division of F_USB below, as it is sourced by
  27 #     F_USB after it has run through any CPU prescalers. Note that this value
  28 #     does not *change* the processor frequency - it should merely be updated to
  29 #     reflect the processor speed set externally so that the code can use accurate
  30 #     software delays.
  31 F_CPU ?= 16000000
  32
  33
  34 #
  35 # LUFA specific
  36 #
  37 # Target architecture (see library "Board Types" documentation).
  38 ARCH ?= AVR8
  39
  40 # Input clock frequency.
  41 #     This will define a symbol, F_USB, in all source code files equal to the
  42 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  43 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  44 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  45 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  46 #     at the end, this will be done automatically to create a 32-bit value in your
  47 #     source code.
  48 #
  49 #     If no clock division is performed on the input clock inside the AVR (via the
  50 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  51 F_USB ?= $(F_CPU)
  52
  53 # Interrupt driven control endpoint task(+60)
  54 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  55
  56
  57 # Boot Section Size in *bytes*
  58 #   Teensy halfKay   512
  59 #   Teensy++ halfKay 1024
  60 #   Atmel DFU loader 4096
  61 #   LUFA bootloader  4096
  62 #   USBaspLoader     2048
  63 BOOTLOADER_SIZE ?= 4096
  64 OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
  65
  66
  67 # Build Options
  68 #   comment out to disable the options.
  69 #
  70 BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
  71 MOUSEKEY_ENABLE ?= yes  # Mouse keys(+4700)
  72 EXTRAKEY_ENABLE ?= yes  # Audio control and System control(+450)
  73 CONSOLE_ENABLE ?= yes   # Console for debug(+400)
  74 COMMAND_ENABLE ?= yes    # Commands for debug and configuration
  75 #SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
  76 #NKRO_ENABLE ?= yes     # USB Nkey Rollover
  77 #ACTIONMAP_ENABLE ?= yes        # Use 16bit action codes in keymap instead of 8bit keycodes
  78
  79
  80 #
  81 # Keymap file
  82 #
  83 ifeq (yes,$(strip $(UNIMAP_ENABLE)))
  84     KEYMAP_FILE = unimap
  85 else
  86     ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
  87         KEYMAP_FILE = actionmap
  88     else
  89         KEYMAP_FILE = keymap
  90     endif
  91 endif
  92 ifdef KEYMAP
  93     SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
  94 else
  95     SRC := $(KEYMAP_FILE)_plain.c $(SRC)
  96 endif
  97
  98
  99 # Optimize size but this may cause error "relocation truncated to fit"
 100 #EXTRALDFLAGS = -Wl,--relax
 101
 102 # Search Path
 103 VPATH += $(TARGET_DIR)
 104 VPATH += $(TMK_DIR)
 105
 106 include $(TMK_DIR)/protocol/lufa.mk
 107 include $(TMK_DIR)/common.mk
 108 include $(TMK_DIR)/rules.mk