keyboard/gh60/Makefile.pjrc

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 TARGET = gh60_pjrc
  43
  44 # Directory common source filess exist
  45 TOP_DIR = ../..
  46
  47 # Directory keyboard dependent files exist
  48 TARGET_DIR = .
  49
  50 # project specific files
  51 SRC =   keymap.c \
  52         matrix.c \
  53         led.c
  54
  55 CONFIG_H = config.h
  56
  57
  58 # MCU name, you MUST set this to match the board you are using
  59 # type "make clean" after changing this, so all files will be rebuilt
  60 MCU = atmega32u4
  61 #MCU = at90usb1286
  62
  63
  64 # Processor frequency.
  65 #   Normally the first thing your program should do is set the clock prescaler,
  66 #   so your program will run at the correct speed.  You should also set this
  67 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  68 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  69 F_CPU = 16000000
  70
  71
  72 # Boot Section Size in *bytes*
  73 #   Teensy halfKay   512
  74 #   Atmel DFU loader 4096
  75 #   LUFA bootloader  4096
  76 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  77
  78
  79 # Build Options
  80 #   comment out to disable the options.
  81 #
  82 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
  83 MOUSEKEY_ENABLE = yes   # Mouse keys(+5000)
  84 EXTRAKEY_ENABLE = yes   # Audio control and System control(+600)
  85 CONSOLE_ENABLE = yes    # Console for debug
  86 COMMAND_ENABLE = yes    # Commands for debug and configuration
  87 SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  88 NKRO_ENABLE = yes       # USB Nkey Rollover(+500)
  89 #PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support
  90
  91
  92 # Search Path
  93 VPATH += $(TARGET_DIR)
  94 VPATH += $(TOP_DIR)
  95
  96 include $(TOP_DIR)/protocol/pjrc.mk
  97 include $(TOP_DIR)/common.mk
  98 include $(TOP_DIR)/rules.mk
  99
 100 plain: OPT_DEFS += -DKEYMAP_PLAIN
 101 plain: all
 102
 103 poker: OPT_DEFS += -DKEYMAP_POKER
 104 poker: all
 105
 106 poker_set: OPT_DEFS += -DKEYMAP_POKER_SET
 107 poker_set: all
 108
 109 poker_bit: OPT_DEFS += -DKEYMAP_POKER_BIT
 110 poker_bit: all