13f77ca9b7db668c9068ba598f2503ecb581f4d0
[tmk_keyboard.git] / converter / usb_usb / Makefile
1 #----------------------------------------------------------------------------
2 # On command line:
3 #
4 # make all = Make software.
5 #
6 # make clean = Clean out built project files.
7 #
8 # make coff = Convert ELF to AVR COFF.
9 #
10 # make extcoff = Convert ELF to AVR Extended COFF.
11 #
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
14 #
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
17 #
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
20 #
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
23 #
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
26 #
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
29 #
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
32 #
33 # make filename.s = Just compile filename.c into the assembler code only.
34 #
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
37 #
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
40
41 # Target file name (without extension).
42 TARGET = usb_usb
43
44 TOP_DIR = ../..
45
46 # Directory keyboard dependent files exist
47 TARGET_DIR = .
48
49 # MCU name
50 MCU = atmega32u4
51
52
53 # Processor frequency.
54 # This will define a symbol, F_CPU, in all source code files equal to the
55 # processor frequency in Hz. You can then use this symbol in your source code to
56 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
57 # automatically to create a 32-bit value in your source code.
58 #
59 # This will be an integer division of F_USB below, as it is sourced by
60 # F_USB after it has run through any CPU prescalers. Note that this value
61 # does not *change* the processor frequency - it should merely be updated to
62 # reflect the processor speed set externally so that the code can use accurate
63 # software delays.
64 F_CPU = 16000000
65
66
67
68 #
69 # LUFA specific
70 #
71 # Target architecture (see library "Board Types" documentation).
72 ARCH = AVR8
73 # Input clock frequency.
74 # This will define a symbol, F_USB, in all source code files equal to the
75 # input clock frequency (before any prescaling is performed) in Hz. This value may
76 # differ from F_CPU if prescaling is used on the latter, and is required as the
77 # raw input clock is fed directly to the PLL sections of the AVR for high speed
78 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
79 # at the end, this will be done automatically to create a 32-bit value in your
80 # source code.
81 #
82 # If no clock division is performed on the input clock inside the AVR (via the
83 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
84 F_USB = $(F_CPU)
85 # Interrupt driven control endpoint task
86 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
87
88
89
90 # Build Options
91 # comment out to disable the options.
92 #
93 MOUSEKEY_ENABLE = yes # Mouse keys
94 EXTRAKEY_ENABLE = yes # Media control and System control
95 CONSOLE_ENABLE = yes # Console for debug
96 #NKRO_ENABLE = yes # USB Nkey Rollover
97
98 # Boot Section Size in bytes
99 # Teensy halfKay 512
100 # Atmel DFU loader 4096
101 # LUFA bootloader 4096
102 #OPT_DEFS += -DBOOTLOADER_SIZE=4096
103
104
105
106 SRC = \
107 keymap.c \
108 matrix.c \
109 led.c \
110 main.cpp
111
112 CONFIG_H = config.h
113
114
115
116 # Search Path
117 VPATH += $(TARGET_DIR)
118 VPATH += $(TOP_DIR)
119
120
121
122 # program Leonardo
123 PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -P$(DEV) -b57600 -Uflash:w:$(TARGET).hex
124
125
126
127 include $(TOP_DIR)/protocol/usb_hid.mk
128 include $(TOP_DIR)/protocol/lufa.mk
129 include $(TOP_DIR)/common.mk
130 include $(TOP_DIR)/rules.mk
Imprint / Impressum