1e69154b8f1f8fdd5e427a21998651c979807ddd
[tmk_keyboard.git] / keyboard / caravan / Makefile
1 #----------------------------------------------------------------------------
2 # On command line:
3 #
4 # make all = Make software.
5 #
6 # make clean = Clean out built project files.
7 #
8 # make coff = Convert ELF to AVR COFF.
9 #
10 # make extcoff = Convert ELF to AVR Extended COFF.
11 #
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
14 #
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
17 #
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
20 #
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
23 #
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
26 #
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
29 #
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
32 #
33 # make filename.s = Just compile filename.c into the assembler code only.
34 #
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
37 #
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
40
41 # Target file name (without extension).
42 TARGET = caravan_lufa
43
44 # Directory common source filess exist
45 TMK_DIR = ../../tmk_core
46
47 # Directory keyboard dependent files exist
48 TARGET_DIR = .
49
50 # project specific files
51 SRC = matrix.c \
52 backlight.c \
53 led.c
54
55 ifdef KEYMAP
56 SRC := keymap_$(KEYMAP).c $(SRC)
57 else
58 SRC := keymap_caravan.c $(SRC)
59 endif
60
61 CONFIG_H = config.h
62
63
64 # MCU name
65 #MCU = at90usb1287
66 MCU = atmega32u4
67
68 # Processor frequency.
69 # This will define a symbol, F_CPU, in all source code files equal to the
70 # processor frequency in Hz. You can then use this symbol in your source code to
71 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
72 # automatically to create a 32-bit value in your source code.
73 #
74 # This will be an integer division of F_USB below, as it is sourced by
75 # F_USB after it has run through any CPU prescalers. Note that this value
76 # does not *change* the processor frequency - it should merely be updated to
77 # reflect the processor speed set externally so that the code can use accurate
78 # software delays.
79 F_CPU = 16000000
80
81
82 #
83 # LUFA specific
84 #
85 # Target architecture (see library "Board Types" documentation).
86 ARCH = AVR8
87
88 # Input clock frequency.
89 # This will define a symbol, F_USB, in all source code files equal to the
90 # input clock frequency (before any prescaling is performed) in Hz. This value may
91 # differ from F_CPU if prescaling is used on the latter, and is required as the
92 # raw input clock is fed directly to the PLL sections of the AVR for high speed
93 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
94 # at the end, this will be done automatically to create a 32-bit value in your
95 # source code.
96 #
97 # If no clock division is performed on the input clock inside the AVR (via the
98 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
99 F_USB = $(F_CPU)
100
101 # Interrupt driven control endpoint task(+60)
102 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
103
104
105 # Boot Section Size in *bytes*
106 # Teensy halfKay 512
107 # Teensy++ halfKay 1024
108 # Atmel DFU loader 4096
109 # LUFA bootloader 4096
110 # USBaspLoader 2048
111 OPT_DEFS += -DBOOTLOADER_SIZE=4096
112
113
114 # Build Options
115 # comment out to disable the options.
116 #
117 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
118 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
119 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
120 CONSOLE_ENABLE = yes # Console for debug(+400)
121 COMMAND_ENABLE = yes # Commands for debug and configuration
122 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
123 NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
124 BACKLIGHT_ENABLE = yes
125
126
127 # Optimize size but this may cause error "relocation truncated to fit"
128 #EXTRALDFLAGS = -Wl,--relax
129
130 # Search Path
131 VPATH += $(TARGET_DIR)
132 VPATH += $(TMK_DIR)
133
134 include $(TMK_DIR)/protocol/lufa.mk
135 include $(TMK_DIR)/common.mk
136 include $(TMK_DIR)/rules.mk
Imprint / Impressum