converter/adb_usb/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 TARGET = adb_usb_lufa
  43
  44 # Directory common source filess exist
  45 TMK_DIR = ../../tmk_core
  46
  47 # Directory keyboard dependent files exist
  48 TARGET_DIR = .
  49
  50 # project specific files
  51 SRC =   matrix.c \
  52         led.c \
  53         adb.c
  54
  55 ifdef KEYMAP
  56     SRC := keymap_$(KEYMAP).c $(SRC)
  57 else
  58     SRC := keymap_plain.c $(SRC)
  59 endif
  60
  61 CONFIG_H = config.h
  62
  63
  64 # MCU name
  65 # atmega32u4    Teensy2.0
  66 # atemga32u4    TMK Converter rev.1
  67 # atemga32u2    TMK Converter rev.2
  68 MCU = atmega32u2
  69
  70 # Processor frequency.
  71 #     This will define a symbol, F_CPU, in all source code files equal to the
  72 #     processor frequency in Hz. You can then use this symbol in your source code to
  73 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  74 #     automatically to create a 32-bit value in your source code.
  75 #
  76 #     This will be an integer division of F_USB below, as it is sourced by
  77 #     F_USB after it has run through any CPU prescalers. Note that this value
  78 #     does not *change* the processor frequency - it should merely be updated to
  79 #     reflect the processor speed set externally so that the code can use accurate
  80 #     software delays.
  81 F_CPU = 16000000
  82
  83
  84 #
  85 # LUFA specific
  86 #
  87 # Target architecture (see library "Board Types" documentation).
  88 ARCH = AVR8
  89
  90 # Input clock frequency.
  91 #     This will define a symbol, F_USB, in all source code files equal to the
  92 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  93 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  94 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  95 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  96 #     at the end, this will be done automatically to create a 32-bit value in your
  97 #     source code.
  98 #
  99 #     If no clock division is performed on the input clock inside the AVR (via the
 100 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 101 F_USB = $(F_CPU)
 102
 103 # Interrupt driven control endpoint task(+60)
 104 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 105
 106
 107 # Boot Section Size in *bytes*
 108 #   Teensy halfKay   512
 109 #   Teensy++ halfKay 1024
 110 #   Atmel DFU loader 4096       for TMK Converter rev.1/rev.2
 111 #   LUFA bootloader  4096
 112 #   USBaspLoader     2048
 113 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 114
 115
 116 # Build Options
 117 #   comment out to disable the options.
 118 #
 119 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
 120 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
 121 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
 122 CONSOLE_ENABLE = yes    # Console for debug(+400)
 123 COMMAND_ENABLE = yes    # Commands for debug and configuration
 124 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
 125 #NKRO_ENABLE = yes      # USB Nkey Rollover
 126 ADB_MOUSE_ENABLE = yes
 127
 128 # ADB Mice need acceleration for todays much bigger screens.
 129 OPT_DEFS += -DADB_MOUSE_MAXACC=8
 130
 131
 132 # Optimize size but this may cause error "relocation truncated to fit"
 133 #EXTRALDFLAGS = -Wl,--relax
 134
 135 # Search Path
 136 VPATH += $(TARGET_DIR)
 137 VPATH += $(TMK_DIR)
 138
 139 include $(TMK_DIR)/protocol/lufa.mk
 140 include $(TMK_DIR)/protocol.mk
 141 include $(TMK_DIR)/common.mk
 142 include $(TMK_DIR)/rules.mk