converter/m0110_usb/Makefile.lufa

   1 # Target file name (without extension).
   2 TARGET = m0110_lufa
   3
   4 # Directory common source filess exist
   5 TOP_DIR = ../..
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR = .
   9
  10 # keyboard dependent files
  11 SRC =   keymap.c \
  12         matrix.c \
  13         led.c \
  14         m0110.c
  15
  16 CONFIG_H = config.h
  17
  18
  19 # MCU name, you MUST set this to match the board you are using
  20 # type "make clean" after changing this, so all files will be rebuilt
  21 #MCU = at90usb162       # Teensy 1.0
  22 MCU = atmega32u4       # Teensy 2.0
  23 #MCU = at90usb646       # Teensy++ 1.0
  24 #MCU = at90usb1286      # Teensy++ 2.0
  25
  26
  27 # Processor frequency.
  28 #   Normally the first thing your program should do is set the clock prescaler,
  29 #   so your program will run at the correct speed.  You should also set this
  30 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  31 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  32 F_CPU = 16000000
  33
  34
  35 #
  36 # LUFA specific
  37 #
  38 # Target architecture (see library "Board Types" documentation).
  39 ARCH = AVR8
  40
  41 # Input clock frequency.
  42 #     This will define a symbol, F_USB, in all source code files equal to the
  43 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  44 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  45 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  46 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  47 #     at the end, this will be done automatically to create a 32-bit value in your
  48 #     source code.
  49 #
  50 #     If no clock division is performed on the input clock inside the AVR (via the
  51 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  52 F_USB = $(F_CPU)
  53
  54 # Interrupt driven control endpoint task
  55 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  56
  57
  58 # Boot Section Size in bytes
  59 #   Teensy halfKay   512
  60 #   Atmel DFU loader 4096
  61 #   LUFA bootloader  4096
  62 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  63
  64
  65 # Build Options
  66 #   comment out to disable the options.
  67 #
  68 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  69 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  70 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  71 CONSOLE_ENABLE = yes    # Console for debug(+400)
  72 COMMAND_ENABLE = yes    # Commands for debug and configuration
  73 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  74 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  75
  76
  77
  78 #---------------- Programming Options --------------------------
  79 PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
  80
  81
  82 # Search Path
  83 VPATH += $(TARGET_DIR)
  84 VPATH += $(TOP_DIR)
  85
  86
  87 include $(TOP_DIR)/protocol/lufa.mk
  88 include $(TOP_DIR)/protocol.mk
  89 include $(TOP_DIR)/common.mk
  90 include $(TOP_DIR)/rules.mk