pana_m8: Add initial files
[tmk_keyboard.git] / converter / sun_usb / Makefile
1 # Target file name (without extension).
2 TARGET = sun_usb
3
4 # Directory common source filess exist
5 TMK_DIR = ../../tmk_core
6
7 # Directory keyboard dependent files exist
8 TARGET_DIR = .
9
10 # keyboard dependent files
11 SRC = keymap.c \
12 matrix.c \
13 led.c \
14 command_extra.c
15
16
17 CONFIG_H = config.h
18
19
20 # MCU name, you MUST set this to match the board you are using
21 # type "make clean" after changing this, so all files will be rebuilt
22 #MCU = at90usb162 # Teensy 1.0
23 #MCU = atmega32u4 # Teensy 2.0
24 #MCU = at90usb646 # Teensy++ 1.0
25 #MCU = at90usb1286 # Teensy++ 2.0
26 MCU = atmega32u2
27
28
29 # Processor frequency.
30 # Normally the first thing your program should do is set the clock prescaler,
31 # so your program will run at the correct speed. You should also set this
32 # variable to same clock speed. The _delay_ms() macro uses this, and many
33 # examples use this variable to calculate timings. Do not add a "UL" here.
34 F_CPU = 16000000
35
36
37 #
38 # LUFA specific
39 #
40 # Target architecture (see library "Board Types" documentation).
41 ARCH = AVR8
42
43 # Input clock frequency.
44 # This will define a symbol, F_USB, in all source code files equal to the
45 # input clock frequency (before any prescaling is performed) in Hz. This value may
46 # differ from F_CPU if prescaling is used on the latter, and is required as the
47 # raw input clock is fed directly to the PLL sections of the AVR for high speed
48 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
49 # at the end, this will be done automatically to create a 32-bit value in your
50 # source code.
51 #
52 # If no clock division is performed on the input clock inside the AVR (via the
53 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
54 F_USB = $(F_CPU)
55
56 # Interrupt driven control endpoint task
57 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
58
59
60 # Build Options
61 # *Comment out* to disable the options.
62 #
63 MOUSEKEY_ENABLE = yes # Mouse keys
64 EXTRAKEY_ENABLE = yes # Audio control and System control
65 CONSOLE_ENABLE = yes # Console for debug
66 COMMAND_ENABLE = yes # Commands for debug and configuration
67 #HARDWARE_SERIAL = yes # Use hardware serial (requires inverted serial, see README)
68 #NKRO_ENABLE = yes # USB Nkey Rollover
69
70 ifdef HARDWARE_SERIAL
71 SRC := protocol/serial_uart.c $(SRC)
72 OPT_DEFS += -DHARDWARE_SERIAL
73 else
74 SRC := protocol/serial_soft.c $(SRC)
75 endif
76
77 # Boot Section Size in bytes
78 # Teensy halfKay 512
79 # Atmel DFU loader 4096
80 # LUFA bootloader 4096
81 OPT_DEFS += -DBOOTLOADER_SIZE=4096
82
83
84 # Search Path
85 VPATH += $(TARGET_DIR)
86 VPATH += $(TMK_DIR)
87
88
89 include $(TMK_DIR)/protocol/lufa.mk
90 include $(TMK_DIR)/protocol.mk
91 include $(TMK_DIR)/common.mk
92 include $(TMK_DIR)/rules.mk
Imprint / Impressum