converter/ps2_usb/Makefile.tmk_rev1

   1 #
   2 # Makefile for TMK keyboard converter rev2
   3 #     https://github.com/tmk/keyboard_converter#pcb-rev1
   4 #
   5 # Target file name (without extension).
   6 TARGET = ps2_usb_tmk_rev1
   7
   8 # Directory common source filess exist
   9 TMK_DIR = ../../tmk_core
  10
  11 # Directory keyboard dependent files exist
  12 TARGET_DIR = .
  13
  14 # project specific files
  15 SRC =   matrix.c \
  16         led.c
  17
  18 ifdef KEYMAP
  19     SRC := keymap_$(KEYMAP).c $(SRC)
  20 else
  21     SRC := keymap_plain.c $(SRC)
  22 endif
  23
  24 CONFIG_H = config_tmk_rev1.h
  25
  26
  27 # MCU name
  28 MCU = atmega32u4
  29
  30 # Processor frequency.
  31 #     This will define a symbol, F_CPU, in all source code files equal to the
  32 #     processor frequency in Hz. You can then use this symbol in your source code to
  33 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  34 #     automatically to create a 32-bit value in your source code.
  35 #
  36 #     This will be an integer division of F_USB below, as it is sourced by
  37 #     F_USB after it has run through any CPU prescalers. Note that this value
  38 #     does not *change* the processor frequency - it should merely be updated to
  39 #     reflect the processor speed set externally so that the code can use accurate
  40 #     software delays.
  41 F_CPU = 16000000
  42
  43
  44 #
  45 # LUFA specific
  46 #
  47 # Target architecture (see library "Board Types" documentation).
  48 ARCH = AVR8
  49
  50 # Input clock frequency.
  51 #     This will define a symbol, F_USB, in all source code files equal to the
  52 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  53 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  54 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  55 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  56 #     at the end, this will be done automatically to create a 32-bit value in your
  57 #     source code.
  58 #
  59 #     If no clock division is performed on the input clock inside the AVR (via the
  60 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  61 F_USB = $(F_CPU)
  62
  63
  64 # Boot Section Size in *bytes*
  65 #   Teensy halfKay   512
  66 #   Teensy++ halfKay 1024
  67 #   Atmel DFU loader 4096
  68 #   LUFA bootloader  4096
  69 #   USBaspLoader     2048
  70 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  71
  72
  73 # Build Options
  74 #   comment out to disable the options.
  75 #
  76 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  77 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  78 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  79 CONSOLE_ENABLE = yes    # Console for debug(+400)
  80 COMMAND_ENABLE = yes    # Commands for debug and configuration
  81 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  82
  83
  84 # PS/2 Options
  85 #
  86 PS2_USE_USART = yes     # uses hardware USART engine for PS/2 signal receive(recomened)
  87 #PS2_USE_BUSYWAIT = yes # uses primitive reference code
  88
  89
  90 # Search Path
  91 VPATH += $(TARGET_DIR)
  92 VPATH += $(TMK_DIR)
  93
  94 include $(TMK_DIR)/protocol.mk
  95 include $(TMK_DIR)/protocol/lufa.mk
  96 include $(TMK_DIR)/common.mk
  97 include $(TMK_DIR)/rules.mk