converter/x68k_usb/Makefile

   1 #
   2 # Makefile for PJRC Teensy
   3 #
   4
   5
   6 # Target file name (without extension).
   7 TARGET = x68k_usb
   8
   9 # Directory common source filess exist
  10 TMK_DIR = ../../tmk_core
  11
  12 # Directory keyboard dependent files exist
  13 TARGET_DIR = .
  14
  15 # keyboard dependent files
  16 SRC =   keymap.c \
  17         matrix.c \
  18         led.c \
  19         protocol/serial_uart.c
  20
  21 CONFIG_H = config.h
  22
  23
  24 # MCU name, you MUST set this to match the board you are using
  25 # type "make clean" after changing this, so all files will be rebuilt
  26 #MCU = at90usb162       # Teensy 1.0
  27 #MCU = atmega32u4       # Teensy 2.0
  28 #MCU = at90usb646       # Teensy++ 1.0
  29 #MCU = at90usb1286      # Teensy++ 2.0
  30 MCU = atmega32u2       # Teensy 2.0
  31
  32
  33 # Processor frequency.
  34 #   Normally the first thing your program should do is set the clock prescaler,
  35 #   so your program will run at the correct speed.  You should also set this
  36 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  37 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  38 F_CPU = 16000000
  39
  40
  41 #
  42 # LUFA specific
  43 #
  44 # Target architecture (see library "Board Types" documentation).
  45 ARCH = AVR8
  46
  47 # Input clock frequency.
  48 #     This will define a symbol, F_USB, in all source code files equal to the
  49 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  50 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  51 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  52 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  53 #     at the end, this will be done automatically to create a 32-bit value in your
  54 #     source code.
  55 #
  56 #     If no clock division is performed on the input clock inside the AVR (via the
  57 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  58 F_USB = $(F_CPU)
  59
  60 # Interrupt driven control endpoint task(+60)
  61 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  62
  63
  64 # Boot Section Size in bytes
  65 #   Teensy halfKay   512
  66 #   Atmel DFU loader 4096
  67 #   LUFA bootloader  4096
  68 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  69
  70
  71 # Build Options
  72 #   *Comment out* to disable the options.
  73 #
  74 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
  75 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  76 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  77 CONSOLE_ENABLE = yes    # Console for debug(+400)
  78 COMMAND_ENABLE = yes    # Commands for debug and configuration
  79 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  80 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  81
  82
  83
  84 #---------------- Programming Options --------------------------
  85 AVRDUDE = avrdude
  86 # Type: avrdude -c ? to get a full listing.
  87 AVRDUDE_PROGRAMMER = avr109
  88 AVRDUDE_PORT = /dev/ttyACM0
  89 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
  90 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
  91
  92 # Uncomment the following if you want avrdude's erase cycle counter.
  93 # Note that this counter needs to be initialized first using -Yn,
  94 # see avrdude manual.
  95 #AVRDUDE_ERASE_COUNTER = -y
  96
  97 # Uncomment the following if you do /not/ wish a verification to be
  98 # performed after programming the device.
  99 #AVRDUDE_NO_VERIFY = -V
 100
 101 # Increase verbosity level.  Please use this when submitting bug
 102 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
 103 # to submit bug reports.
 104 #AVRDUDE_VERBOSE = -v -v
 105
 106 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
 107 #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
 108 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
 109 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
 110 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 111
 112 PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
 113
 114
 115 # Search Path
 116 VPATH += $(TARGET_DIR)
 117 VPATH += $(TMK_DIR)
 118
 119
 120 include $(TMK_DIR)/protocol.mk
 121 include $(TMK_DIR)/protocol/lufa.mk
 122 include $(TMK_DIR)/common.mk
 123 include $(TMK_DIR)/rules.mk