converter/usb_usb/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 TARGET ?= usb_usb
  43
  44 TMK_DIR ?= ../../tmk_core
  45
  46 # Directory keyboard dependent files exist
  47 TARGET_DIR ?= .
  48
  49 # MCU name
  50 MCU ?= atmega32u4
  51
  52
  53 # Processor frequency.
  54 #     This will define a symbol, F_CPU, in all source code files equal to the
  55 #     processor frequency in Hz. You can then use this symbol in your source code to
  56 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  57 #     automatically to create a 32-bit value in your source code.
  58 #
  59 #     This will be an integer division of F_USB below, as it is sourced by
  60 #     F_USB after it has run through any CPU prescalers. Note that this value
  61 #     does not *change* the processor frequency - it should merely be updated to
  62 #     reflect the processor speed set externally so that the code can use accurate
  63 #     software delays.
  64 F_CPU ?= 16000000
  65
  66
  67
  68 #
  69 # LUFA specific
  70 #
  71 # Target architecture (see library "Board Types" documentation).
  72 ARCH ?= AVR8
  73 # Input clock frequency.
  74 #     This will define a symbol, F_USB, in all source code files equal to the
  75 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  76 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  77 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  78 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  79 #     at the end, this will be done automatically to create a 32-bit value in your
  80 #     source code.
  81 #
  82 #     If no clock division is performed on the input clock inside the AVR (via the
  83 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  84 F_USB ?= $(F_CPU)
  85 # Interrupt driven control endpoint task
  86 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  87
  88
  89
  90 # Build Options
  91 #   comment out to disable the options.
  92 #
  93 MOUSEKEY_ENABLE ?= yes  # Mouse keys
  94 EXTRAKEY_ENABLE ?= yes  # Media control and System control
  95 CONSOLE_ENABLE ?= yes   # Console for debug
  96 #COMMAND_ENABLE ?= yes    # Commands for debug and configuration
  97 #NKRO_ENABLE ?= yes     # USB Nkey Rollover
  98
  99 # Boot Section Size in bytes
 100 #   Teensy halfKay   512
 101 #   Atmel DFU loader 4096
 102 #   LUFA bootloader  4096
 103 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 104
 105 #LDFLAGS += -Wl,--relax
 106
 107 #OPT_DEFS += -DNO_ACTION_TAPPING
 108 #OPT_DEFS += -DNO_ACTION_LAYER
 109 #OPT_DEFS += -DNO_ACTION_MACRO
 110
 111 SRC ?=  usb_usb.cpp \
 112        main.cpp
 113
 114 #
 115 # Keymap file
 116 #
 117 ifeq (yes,$(strip $(UNIMAP_ENABLE)))
 118     KEYMAP_FILE = unimap
 119 else
 120     ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
 121         KEYMAP_FILE = actionmap
 122     else
 123         KEYMAP_FILE = keymap
 124     endif
 125 endif
 126 ifdef KEYMAP
 127     SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
 128 else
 129     SRC := $(KEYMAP_FILE).c $(SRC)
 130 endif
 131
 132 CONFIG_H ?= config.h
 133
 134
 135
 136 # Search Path
 137 VPATH += $(TARGET_DIR)
 138 VPATH += $(TMK_DIR)
 139
 140
 141
 142 # program Leonardo
 143 PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -b57600 -Uflash:w:$(TARGET).hex -P$(DEV)
 144
 145
 146
 147 include $(TMK_DIR)/protocol/usb_hid.mk
 148 include $(TMK_DIR)/protocol/lufa.mk
 149 include $(TMK_DIR)/common.mk
 150 include $(TMK_DIR)/rules.mk