keyboard/gh60/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 TARGET = gh60_lufa
  43
  44 # Directory common source filess exist
  45 TMK_DIR = ../../tmk_core
  46
  47 # Directory keyboard dependent files exist
  48 TARGET_DIR = .
  49
  50 # project specific files
  51 SRC =   keymap_common.c \
  52         matrix.c \
  53         led.c
  54
  55 ifdef KEYMAP
  56     SRC := keymap_$(KEYMAP).c $(SRC)
  57 else
  58     SRC := keymap_poker.c $(SRC)
  59 endif
  60
  61 CONFIG_H = config.h
  62
  63
  64 # MCU name
  65 #MCU = at90usb1287
  66 MCU = atmega32u4
  67
  68 # Processor frequency.
  69 #     This will define a symbol, F_CPU, in all source code files equal to the
  70 #     processor frequency in Hz. You can then use this symbol in your source code to
  71 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  72 #     automatically to create a 32-bit value in your source code.
  73 #
  74 #     This will be an integer division of F_USB below, as it is sourced by
  75 #     F_USB after it has run through any CPU prescalers. Note that this value
  76 #     does not *change* the processor frequency - it should merely be updated to
  77 #     reflect the processor speed set externally so that the code can use accurate
  78 #     software delays.
  79 F_CPU = 16000000
  80
  81
  82 #
  83 # LUFA specific
  84 #
  85 # Target architecture (see library "Board Types" documentation).
  86 ARCH = AVR8
  87
  88 # Input clock frequency.
  89 #     This will define a symbol, F_USB, in all source code files equal to the
  90 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  91 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  92 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  93 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  94 #     at the end, this will be done automatically to create a 32-bit value in your
  95 #     source code.
  96 #
  97 #     If no clock division is performed on the input clock inside the AVR (via the
  98 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  99 F_USB = $(F_CPU)
 100
 101 # Interrupt driven control endpoint task(+60)
 102 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 103
 104
 105 # Boot Section Size in *bytes*
 106 #   Teensy halfKay   512
 107 #   Teensy++ halfKay 1024
 108 #   Atmel DFU loader 4096
 109 #   LUFA bootloader  4096
 110 #   USBaspLoader     2048
 111 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 112
 113
 114 # Build Options
 115 #   comment out to disable the options.
 116 #
 117 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
 118 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
 119 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
 120 CONSOLE_ENABLE = yes    # Console for debug(+400)
 121 COMMAND_ENABLE = yes    # Commands for debug and configuration
 122 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
 123 NKRO_ENABLE = yes       # USB Nkey Rollover - not yet supported in LUFA
 124
 125
 126 # Optimize size but this may cause error "relocation truncated to fit"
 127 #EXTRALDFLAGS = -Wl,--relax
 128
 129 # Search Path
 130 VPATH += $(TARGET_DIR)
 131 VPATH += $(TMK_DIR)
 132
 133 include $(TMK_DIR)/protocol/lufa.mk
 134 include $(TMK_DIR)/common.mk
 135 include $(TMK_DIR)/rules.mk