644845f91c533a72a9e873146186a0dd74a2fe05
[tmk_keyboard.git] / converter / ps2_usb / Makefile.tmk_rev1
1 #
2 # Makefile for TMK keyboard converter rev2
3 # https://github.com/tmk/keyboard_converter#pcb-rev1
4 #
5 # Target file name (without extension).
6 TARGET = ps2_usb_tmk_rev1
7
8 # Directory common source filess exist
9 TMK_DIR = ../../tmk_core
10
11 # Directory keyboard dependent files exist
12 TARGET_DIR = .
13
14 # project specific files
15 SRC = matrix.c \
16 led.c
17
18 ifdef KEYMAP
19 SRC := keymap_$(KEYMAP).c $(SRC)
20 else
21 SRC := keymap_plain.c $(SRC)
22 endif
23
24 CONFIG_H = config_tmk_rev1.h
25
26
27 # MCU name
28 MCU = atmega32u4
29
30 # Processor frequency.
31 # This will define a symbol, F_CPU, in all source code files equal to the
32 # processor frequency in Hz. You can then use this symbol in your source code to
33 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
34 # automatically to create a 32-bit value in your source code.
35 #
36 # This will be an integer division of F_USB below, as it is sourced by
37 # F_USB after it has run through any CPU prescalers. Note that this value
38 # does not *change* the processor frequency - it should merely be updated to
39 # reflect the processor speed set externally so that the code can use accurate
40 # software delays.
41 F_CPU = 16000000
42
43
44 #
45 # LUFA specific
46 #
47 # Target architecture (see library "Board Types" documentation).
48 ARCH = AVR8
49
50 # Input clock frequency.
51 # This will define a symbol, F_USB, in all source code files equal to the
52 # input clock frequency (before any prescaling is performed) in Hz. This value may
53 # differ from F_CPU if prescaling is used on the latter, and is required as the
54 # raw input clock is fed directly to the PLL sections of the AVR for high speed
55 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
56 # at the end, this will be done automatically to create a 32-bit value in your
57 # source code.
58 #
59 # If no clock division is performed on the input clock inside the AVR (via the
60 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
61 F_USB = $(F_CPU)
62
63
64 # Boot Section Size in *bytes*
65 # Teensy halfKay 512
66 # Teensy++ halfKay 1024
67 # Atmel DFU loader 4096
68 # LUFA bootloader 4096
69 # USBaspLoader 2048
70 OPT_DEFS += -DBOOTLOADER_SIZE=4096
71
72
73 # Build Options
74 # comment out to disable the options.
75 #
76 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
77 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
78 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
79 CONSOLE_ENABLE = yes # Console for debug(+400)
80 COMMAND_ENABLE = yes # Commands for debug and configuration
81 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
82
83
84 # PS/2 Options
85 #
86 PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
87 #PS2_USE_BUSYWAIT = yes # uses primitive reference code
88
89
90 # Search Path
91 VPATH += $(TARGET_DIR)
92 VPATH += $(TMK_DIR)
93
94 include $(TMK_DIR)/protocol.mk
95 include $(TMK_DIR)/protocol/lufa.mk
96 include $(TMK_DIR)/common.mk
97 include $(TMK_DIR)/rules.mk
Imprint / Impressum