converter/m0110_usb/Makefile

   1 # Target file name (without extension).
   2 TARGET = m0110_lufa
   3
   4 # Directory common source filess exist
   5 TOP_DIR = ../..
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR = .
   9
  10 # keyboard dependent files
  11 SRC =   matrix.c \
  12         led.c \
  13         keymap_common.c \
  14         m0110.c
  15
  16 # To use own keymap file run make like: make keymap=hasu
  17 ifdef KEYMAP
  18     SRC += keymap_$(KEYMAP).c
  19 else
  20     SRC += keymap_default.c
  21 endif
  22
  23 CONFIG_H = config.h
  24
  25
  26 # MCU name, you MUST set this to match the board you are using
  27 # type "make clean" after changing this, so all files will be rebuilt
  28 MCU = atmega32u2       # TMK converter rev2
  29 #MCU = atmega32u4       # TMK converter rev1
  30
  31
  32 # Processor frequency.
  33 #   Normally the first thing your program should do is set the clock prescaler,
  34 #   so your program will run at the correct speed.  You should also set this
  35 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  36 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  37 F_CPU = 16000000
  38
  39
  40 #
  41 # LUFA specific
  42 #
  43 # Target architecture (see library "Board Types" documentation).
  44 ARCH = AVR8
  45
  46 # Input clock frequency.
  47 #     This will define a symbol, F_USB, in all source code files equal to the
  48 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  49 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  50 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  51 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  52 #     at the end, this will be done automatically to create a 32-bit value in your
  53 #     source code.
  54 #
  55 #     If no clock division is performed on the input clock inside the AVR (via the
  56 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  57 F_USB = $(F_CPU)
  58
  59 # Interrupt driven control endpoint task
  60 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  61
  62
  63 # Boot Section Size in bytes
  64 #   Teensy halfKay   512
  65 #   Atmel DFU loader 4096
  66 #   LUFA bootloader  4096
  67 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  68
  69
  70 # Build Options
  71 #   *Comment out* to disable the options.
  72 #
  73 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  74 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  75 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  76 CONSOLE_ENABLE = yes    # Console for debug(+400)
  77 COMMAND_ENABLE = yes    # Commands for debug and configuration
  78 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  79 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  80 #KEYMAP_SECTION_ENABLE = yes    # fixed address keymap for keymap editor
  81
  82
  83
  84 #---------------- Programming Options --------------------------
  85 PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
  86
  87
  88 # Search Path
  89 VPATH += $(TARGET_DIR)
  90 VPATH += $(TOP_DIR)
  91
  92
  93 include $(TOP_DIR)/protocol/lufa.mk
  94 include $(TOP_DIR)/protocol.mk
  95 include $(TOP_DIR)/common.mk
  96 include $(TOP_DIR)/rules.mk