keyboard/onekey/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 TARGET = onekey_lufa
  43
  44 # Directory common source filess exist
  45 TOP_DIR = ../..
  46
  47 # Directory keyboard dependent files exist
  48 TARGET_DIR = .
  49
  50 # project specific files
  51 SRC =   keymap.c \
  52         matrix.c \
  53         led.c
  54
  55 CONFIG_H = config.h
  56
  57
  58 # MCU name
  59 #MCU = at90usb1287
  60 MCU = atmega32u4
  61
  62 # Processor frequency.
  63 #     This will define a symbol, F_CPU, in all source code files equal to the
  64 #     processor frequency in Hz. You can then use this symbol in your source code to
  65 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  66 #     automatically to create a 32-bit value in your source code.
  67 #
  68 #     This will be an integer division of F_USB below, as it is sourced by
  69 #     F_USB after it has run through any CPU prescalers. Note that this value
  70 #     does not *change* the processor frequency - it should merely be updated to
  71 #     reflect the processor speed set externally so that the code can use accurate
  72 #     software delays.
  73 F_CPU = 16000000
  74
  75
  76 #
  77 # LUFA specific
  78 #
  79 # Target architecture (see library "Board Types" documentation).
  80 ARCH = AVR8
  81
  82 # Input clock frequency.
  83 #     This will define a symbol, F_USB, in all source code files equal to the
  84 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  85 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  86 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  87 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  88 #     at the end, this will be done automatically to create a 32-bit value in your
  89 #     source code.
  90 #
  91 #     If no clock division is performed on the input clock inside the AVR (via the
  92 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  93 F_USB = $(F_CPU)
  94
  95 # Interrupt driven control endpoint task(+60)
  96 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  97
  98
  99 # Boot Section Size in *bytes*
 100 #   Teensy halfKay   512
 101 #   Teensy++ halfKay 1024
 102 #   Atmel DFU loader 4096
 103 #   LUFA bootloader  4096
 104 #   USBaspLoader     2048
 105 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 106
 107
 108 # Build Options
 109 #   comment out to disable the options.
 110 #
 111 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
 112 #MOUSEKEY_ENABLE = yes  # Mouse keys(+4700)
 113 #EXTRAKEY_ENABLE = yes  # Audio control and System control(+450)
 114 CONSOLE_ENABLE = yes    # Console for debug(+400)
 115 #COMMAND_ENABLE = yes    # Commands for debug and configuration
 116 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
 117 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
 118
 119 #PS2_MOUSE_ENABLE = yes  # PS/2 mouse(TrackPoint) support
 120 #PS2_USE_BUSYWAIT = yes # uses primitive reference code
 121 #PS2_USE_INT = yes      # uses external interrupt for falling edge of PS/2 clock pin
 122 #PS2_USE_USART = yes     # uses hardware USART engine for PS/2 signal receive(recomened)
 123
 124
 125 # Search Path
 126 VPATH += $(TARGET_DIR)
 127 VPATH += $(TOP_DIR)
 128
 129 include $(TOP_DIR)/common.mk
 130 include $(TOP_DIR)/protocol.mk
 131 include $(TOP_DIR)/protocol/lufa.mk
 132 include $(TOP_DIR)/rules.mk