]>
git.gir.st - tmk_keyboard.git/blob - converter/ps2_usb/Makefile
4 # Target file name (without extension).
7 # Directory common source filess exist
10 # Directory keyboard dependent files exist
13 # project specific files
14 SRC
= keymap_common.c \
19 SRC
:= keymap_
$(KEYMAP
).c
$(SRC
)
21 SRC
:= keymap_plain.c
$(SRC
)
31 # Processor frequency.
32 # This will define a symbol, F_CPU, in all source code files equal to the
33 # processor frequency in Hz. You can then use this symbol in your source code to
34 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
35 # automatically to create a 32-bit value in your source code.
37 # This will be an integer division of F_USB below, as it is sourced by
38 # F_USB after it has run through any CPU prescalers. Note that this value
39 # does not *change* the processor frequency - it should merely be updated to
40 # reflect the processor speed set externally so that the code can use accurate
48 # Target architecture (see library "Board Types" documentation).
51 # Input clock frequency.
52 # This will define a symbol, F_USB, in all source code files equal to the
53 # input clock frequency (before any prescaling is performed) in Hz. This value may
54 # differ from F_CPU if prescaling is used on the latter, and is required as the
55 # raw input clock is fed directly to the PLL sections of the AVR for high speed
56 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
57 # at the end, this will be done automatically to create a 32-bit value in your
60 # If no clock division is performed on the input clock inside the AVR (via the
61 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
64 # Interrupt driven control endpoint task(+60)
65 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
68 # Boot Section Size in *bytes*
70 # Teensy++ halfKay 1024
71 # Atmel DFU loader 4096
72 # LUFA bootloader 4096
74 OPT_DEFS
+= -DBOOTLOADER_SIZE
=512
78 # comment out to disable the options.
80 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
81 MOUSEKEY_ENABLE
= yes
# Mouse keys(+4700)
82 EXTRAKEY_ENABLE
= yes
# Audio control and System control(+450)
83 CONSOLE_ENABLE
= yes
# Console for debug(+400)
84 COMMAND_ENABLE
= yes
# Commands for debug and configuration
85 NKRO_ENABLE
= yes
# USB Nkey Rollover - not yet supported in LUFA
90 PS2_USE_USART
= yes
# uses hardware USART engine for PS/2 signal receive(recomened)
91 #PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
92 #PS2_USE_BUSYWAIT = yes # uses primitive reference code
94 # Serial Mouse Options
95 # You can choose a mouse protocol and the implementation of
96 # the underlying serial connection.
98 #SERIAL_MOUSE_MICROSOFT_ENABLE = yes # Enable support for Microsoft-compatible mice
99 #SERIAL_MOUSE_MOUSESYSTEMS_ENABLE = yes # Enable support for Mousesystems-compatible mice
100 #SERIAL_MOUSE_USE_UART = yes # use hardware UART for serial connection
101 #SERIAL_MOUSE_USE_SOFT = yes # use software serial implementation
103 # Optional serial mouse driver features
104 # Support scrolling while holding the middle mouse button
105 # (currently only supported for Mousesystems mice):
106 #OPT_DEFS += -DSERIAL_MOUSE_CENTER_SCROLL
108 # Optimize size but this may cause error "relocation truncated to fit"
109 #EXTRALDFLAGS = -Wl,--relax
112 VPATH
+= $(TARGET_DIR
)
115 include $(TOP_DIR
)/protocol.mk
116 include $(TOP_DIR
)/protocol
/lufa.mk
117 include $(TOP_DIR
)/common.mk
118 include $(TOP_DIR
)/rules.mk