converter/m0110_usb/Makefile

   1 # Target file name (without extension).
   2 TARGET = m0110_lufa
   3
   4 # Directory common source filess exist
   5 TOP_DIR = ../..
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR = .
   9
  10 # keyboard dependent files
  11 SRC =   matrix.c \
  12         led.c \
  13         m0110.c
  14
  15 # To use own keymap file run make like: make keymap=hasu
  16 ifdef keymap
  17     SRC += keymap_$(keymap).c
  18 else
  19     SRC += keymap.c
  20 endif
  21
  22 CONFIG_H = config.h
  23
  24
  25 # MCU name, you MUST set this to match the board you are using
  26 # type "make clean" after changing this, so all files will be rebuilt
  27 #MCU = at90usb162       # Teensy 1.0
  28 MCU = atmega32u4       # Teensy 2.0
  29 #MCU = at90usb646       # Teensy++ 1.0
  30 #MCU = at90usb1286      # Teensy++ 2.0
  31
  32
  33 # Processor frequency.
  34 #   Normally the first thing your program should do is set the clock prescaler,
  35 #   so your program will run at the correct speed.  You should also set this
  36 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  37 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  38 F_CPU = 16000000
  39
  40
  41 #
  42 # LUFA specific
  43 #
  44 # Target architecture (see library "Board Types" documentation).
  45 ARCH = AVR8
  46
  47 # Input clock frequency.
  48 #     This will define a symbol, F_USB, in all source code files equal to the
  49 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  50 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  51 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  52 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  53 #     at the end, this will be done automatically to create a 32-bit value in your
  54 #     source code.
  55 #
  56 #     If no clock division is performed on the input clock inside the AVR (via the
  57 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  58 F_USB = $(F_CPU)
  59
  60 # Interrupt driven control endpoint task
  61 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  62
  63
  64 # Boot Section Size in bytes
  65 #   Teensy halfKay   512
  66 #   Atmel DFU loader 4096
  67 #   LUFA bootloader  4096
  68 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  69
  70
  71 # Build Options
  72 #   *Comment out* to disable the options.
  73 #
  74 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
  75 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  76 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  77 CONSOLE_ENABLE = yes    # Console for debug(+400)
  78 COMMAND_ENABLE = yes    # Commands for debug and configuration
  79 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  80 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  81
  82
  83
  84 #---------------- Programming Options --------------------------
  85 PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
  86
  87
  88 # Search Path
  89 VPATH += $(TARGET_DIR)
  90 VPATH += $(TOP_DIR)
  91
  92
  93 include $(TOP_DIR)/protocol/lufa.mk
  94 include $(TOP_DIR)/protocol.mk
  95 include $(TOP_DIR)/common.mk
  96 include $(TOP_DIR)/rules.mk