converter/ps2_usb/Makefile

   1 # Target file name (without extension).
   2 TARGET ?= ps2_usb
   3
   4 # Directory common source filess exist
   5 TMK_DIR ?= ../../tmk_core
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR ?= .
   9
  10 # project specific files
  11 SRC ?=  matrix.c \
  12         led.c
  13
  14 #
  15 # Keymap file
  16 #
  17 ifdef UNIMAP_ENABLE
  18     KEYMAP_FILE = unimap
  19 else
  20     ifdef ACTIONMAP_ENABLE
  21         KEYMAP_FILE = actionmap
  22     else
  23         KEYMAP_FILE = keymap
  24     endif
  25 endif
  26 ifdef KEYMAP
  27     SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
  28 else
  29     SRC := $(KEYMAP_FILE)_plain.c $(SRC)
  30 endif
  31
  32 CONFIG_H ?= config.h
  33
  34
  35 # MCU name
  36 MCU ?= atmega32u2
  37
  38 # Processor frequency.
  39 #     This will define a symbol, F_CPU, in all source code files equal to the
  40 #     processor frequency in Hz. You can then use this symbol in your source code to
  41 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  42 #     automatically to create a 32-bit value in your source code.
  43 #
  44 #     This will be an integer division of F_USB below, as it is sourced by
  45 #     F_USB after it has run through any CPU prescalers. Note that this value
  46 #     does not *change* the processor frequency - it should merely be updated to
  47 #     reflect the processor speed set externally so that the code can use accurate
  48 #     software delays.
  49 F_CPU ?= 16000000
  50
  51
  52 #
  53 # LUFA specific
  54 #
  55 # Target architecture (see library "Board Types" documentation).
  56 ARCH ?= AVR8
  57
  58 # Input clock frequency.
  59 #     This will define a symbol, F_USB, in all source code files equal to the
  60 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  61 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  62 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  63 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  64 #     at the end, this will be done automatically to create a 32-bit value in your
  65 #     source code.
  66 #
  67 #     If no clock division is performed on the input clock inside the AVR (via the
  68 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  69 F_USB ?= $(F_CPU)
  70
  71 # Interrupt driven control endpoint task
  72 # Not work with suart debug
  73 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  74
  75 # This improves response of keyboard when wakeup
  76 OPT_DEFS += -DSUSPEND_MODE_STANDBY
  77
  78 # Boot Section Size in *bytes*
  79 #   Teensy halfKay   512
  80 #   Teensy++ halfKay 1024
  81 #   Atmel DFU loader 4096
  82 #   LUFA bootloader  4096
  83 #   USBaspLoader     2048
  84 BOOTLOADER_SIZE ?= 4096
  85 OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
  86
  87
  88 # Build Options
  89 #   comment out to disable the options.
  90 #
  91 BOOTMAGIC_ENABLE ?= no  # Virtual DIP switch configuration(+1000)
  92 MOUSEKEY_ENABLE ?= no   # Mouse keys(+4700)
  93 EXTRAKEY_ENABLE ?= yes  # Audio control and System control(+450)
  94 CONSOLE_ENABLE ?= yes   # Console for debug(+400)
  95 COMMAND_ENABLE ?= yes    # Commands for debug and configuration
  96 NKRO_ENABLE ?= yes      # USB Nkey Rollover
  97
  98
  99 # PS/2 Options
 100 #
 101 #PS2_USE_USART ?= yes   # uses hardware USART engine for PS/2 signal receive(recomened)
 102 PS2_USE_INT ?= yes      # uses external interrupt for falling edge of PS/2 clock pin
 103 #PS2_USE_BUSYWAIT ?= yes        # uses primitive reference code
 104
 105
 106 # Optimize size but this may cause error "relocation truncated to fit"
 107 #EXTRALDFLAGS = -Wl,--relax
 108
 109 # Search Path
 110 VPATH += $(TARGET_DIR)
 111 VPATH += $(TMK_DIR)
 112
 113 include $(TMK_DIR)/protocol.mk
 114 include $(TMK_DIR)/protocol/lufa.mk
 115 include $(TMK_DIR)/common.mk
 116 include $(TMK_DIR)/rules.mk