remove experimental return, cleanup slash_question key
[tmk_keyboard.git] / converter / ps2_usb / Makefile
1 # Target file name (without extension).
2 TARGET ?= ps2_usb
3
4 # Directory common source filess exist
5 TMK_DIR ?= ../../tmk_core
6
7 # Directory keyboard dependent files exist
8 TARGET_DIR ?= .
9
10 # project specific files
11 SRC ?= matrix.c \
12 led.c
13
14 #
15 # Keymap file
16 #
17 ifdef UNIMAP_ENABLE
18 KEYMAP_FILE = unimap
19 else
20 ifdef ACTIONMAP_ENABLE
21 KEYMAP_FILE = actionmap
22 else
23 KEYMAP_FILE = keymap
24 endif
25 endif
26 ifdef KEYMAP
27 SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
28 else
29 SRC := $(KEYMAP_FILE)_plain.c $(SRC)
30 endif
31
32 CONFIG_H ?= config.h
33
34
35 # MCU name
36 MCU ?= atmega32u2
37
38 # Processor frequency.
39 # This will define a symbol, F_CPU, in all source code files equal to the
40 # processor frequency in Hz. You can then use this symbol in your source code to
41 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
42 # automatically to create a 32-bit value in your source code.
43 #
44 # This will be an integer division of F_USB below, as it is sourced by
45 # F_USB after it has run through any CPU prescalers. Note that this value
46 # does not *change* the processor frequency - it should merely be updated to
47 # reflect the processor speed set externally so that the code can use accurate
48 # software delays.
49 F_CPU ?= 16000000
50
51
52 #
53 # LUFA specific
54 #
55 # Target architecture (see library "Board Types" documentation).
56 ARCH ?= AVR8
57
58 # Input clock frequency.
59 # This will define a symbol, F_USB, in all source code files equal to the
60 # input clock frequency (before any prescaling is performed) in Hz. This value may
61 # differ from F_CPU if prescaling is used on the latter, and is required as the
62 # raw input clock is fed directly to the PLL sections of the AVR for high speed
63 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
64 # at the end, this will be done automatically to create a 32-bit value in your
65 # source code.
66 #
67 # If no clock division is performed on the input clock inside the AVR (via the
68 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
69 F_USB ?= $(F_CPU)
70
71 # Interrupt driven control endpoint task
72 # Not work with suart debug
73 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
74
75 # This improves response of keyboard when wakeup
76 OPT_DEFS += -DSUSPEND_MODE_STANDBY
77
78 # Boot Section Size in *bytes*
79 # Teensy halfKay 512
80 # Teensy++ halfKay 1024
81 # Atmel DFU loader 4096
82 # LUFA bootloader 4096
83 # USBaspLoader 2048
84 BOOTLOADER_SIZE ?= 4096
85 OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
86
87
88 # Build Options
89 # comment out to disable the options.
90 #
91 BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
92 MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
93 EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
94 CONSOLE_ENABLE ?= yes # Console for debug(+400)
95 COMMAND_ENABLE ?= yes # Commands for debug and configuration
96 NKRO_ENABLE ?= yes # USB Nkey Rollover
97
98
99 # PS/2 Options
100 #
101 #PS2_USE_USART ?= yes # uses hardware USART engine for PS/2 signal receive(recomened)
102 PS2_USE_INT ?= yes # uses external interrupt for falling edge of PS/2 clock pin
103 #PS2_USE_BUSYWAIT ?= yes # uses primitive reference code
104
105
106 # Optimize size but this may cause error "relocation truncated to fit"
107 #EXTRALDFLAGS = -Wl,--relax
108
109 # Search Path
110 VPATH += $(TARGET_DIR)
111 VPATH += $(TMK_DIR)
112
113 include $(TMK_DIR)/protocol.mk
114 include $(TMK_DIR)/protocol/lufa.mk
115 include $(TMK_DIR)/common.mk
116 include $(TMK_DIR)/rules.mk
Imprint / Impressum