remove experimental return, cleanup slash_question key
[tmk_keyboard.git] / keyboard / caravan / Makefile
1 #----------------------------------------------------------------------------
2 # On command line:
3 #
4 # make all = Make software.
5 #
6 # make clean = Clean out built project files.
7 #
8 # make coff = Convert ELF to AVR COFF.
9 #
10 # make extcoff = Convert ELF to AVR Extended COFF.
11 #
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
14 #
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
17 #
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
20 #
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
23 #
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
26 #
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
29 #
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
32 #
33 # make filename.s = Just compile filename.c into the assembler code only.
34 #
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
37 #
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
40
41 # Target file name (without extension).
42 ifdef TARGETFILE
43 TARGET = $(TARGETFILE)
44 else
45 TARGET = caravan_lufa
46 endif
47
48 # Directory common source filess exist
49 TMK_DIR = ../../tmk_core
50
51 # Directory keyboard dependent files exist
52 TARGET_DIR = .
53
54 # project specific files
55 SRC = matrix.c \
56 backlight.c \
57 led.c
58
59 ifdef KEYMAP
60 SRC := keymap_$(KEYMAP).c $(SRC)
61 else
62 SRC := keymap_caravan.c $(SRC)
63 endif
64
65 CONFIG_H = config.h
66
67
68 # MCU name
69 #MCU = at90usb1287
70 MCU = atmega32u4
71
72 # Processor frequency.
73 # This will define a symbol, F_CPU, in all source code files equal to the
74 # processor frequency in Hz. You can then use this symbol in your source code to
75 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
76 # automatically to create a 32-bit value in your source code.
77 #
78 # This will be an integer division of F_USB below, as it is sourced by
79 # F_USB after it has run through any CPU prescalers. Note that this value
80 # does not *change* the processor frequency - it should merely be updated to
81 # reflect the processor speed set externally so that the code can use accurate
82 # software delays.
83 F_CPU = 16000000
84
85
86 #
87 # LUFA specific
88 #
89 # Target architecture (see library "Board Types" documentation).
90 ARCH = AVR8
91
92 # Input clock frequency.
93 # This will define a symbol, F_USB, in all source code files equal to the
94 # input clock frequency (before any prescaling is performed) in Hz. This value may
95 # differ from F_CPU if prescaling is used on the latter, and is required as the
96 # raw input clock is fed directly to the PLL sections of the AVR for high speed
97 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
98 # at the end, this will be done automatically to create a 32-bit value in your
99 # source code.
100 #
101 # If no clock division is performed on the input clock inside the AVR (via the
102 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
103 F_USB = $(F_CPU)
104
105 # Interrupt driven control endpoint task(+60)
106 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
107
108
109 # Boot Section Size in *bytes*
110 # Teensy halfKay 512
111 # Teensy++ halfKay 1024
112 # Atmel DFU loader 4096
113 # LUFA bootloader 4096
114 # USBaspLoader 2048
115 OPT_DEFS += -DBOOTLOADER_SIZE=4096
116
117
118 # Build Options
119 # comment out to disable the options.
120 #
121 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
122 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
123 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
124 CONSOLE_ENABLE = yes # Console for debug(+400)
125 COMMAND_ENABLE = yes # Commands for debug and configuration
126 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
127 NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
128 BACKLIGHT_ENABLE = yes
129
130
131 # Optimize size but this may cause error "relocation truncated to fit"
132 #EXTRALDFLAGS = -Wl,--relax
133
134 # Search Path
135 VPATH += $(TARGET_DIR)
136 VPATH += $(TMK_DIR)
137
138 include $(TMK_DIR)/protocol/lufa.mk
139 include $(TMK_DIR)/common.mk
140 include $(TMK_DIR)/rules.mk
Imprint / Impressum