converter/x68k_usb/Makefile

   1 # Target file name (without extension).
   2 TARGET ?= x68k_usb
   3
   4 # Directory common source filess exist
   5 TMK_DIR ?= ../../tmk_core
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR ?= .
   9
  10 # project specific files
  11 SRC ?=  matrix.c \
  12         led.c \
  13         protocol/serial_uart.c
  14
  15 CONFIG_H = config.h
  16
  17
  18 # MCU name
  19 # atmega32u4    Teensy2.0
  20 # atemga32u4    TMK Converter rev.1
  21 # atemga32u2    TMK Converter rev.2
  22 MCU ?= atmega32u2
  23
  24 # Processor frequency.
  25 #     This will define a symbol, F_CPU, in all source code files equal to the
  26 #     processor frequency in Hz. You can then use this symbol in your source code to
  27 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  28 #     automatically to create a 32-bit value in your source code.
  29 #
  30 #     This will be an integer division of F_USB below, as it is sourced by
  31 #     F_USB after it has run through any CPU prescalers. Note that this value
  32 #     does not *change* the processor frequency - it should merely be updated to
  33 #     reflect the processor speed set externally so that the code can use accurate
  34 #     software delays.
  35 F_CPU ?= 16000000
  36
  37
  38 #
  39 # LUFA specific
  40 #
  41 # Target architecture (see library "Board Types" documentation).
  42 ARCH ?= AVR8
  43
  44 # Input clock frequency.
  45 #     This will define a symbol, F_USB, in all source code files equal to the
  46 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  47 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  48 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  49 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  50 #     at the end, this will be done automatically to create a 32-bit value in your
  51 #     source code.
  52 #
  53 #     If no clock division is performed on the input clock inside the AVR (via the
  54 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  55 F_USB ?= $(F_CPU)
  56
  57 # Interrupt driven control endpoint task(+60)
  58 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  59
  60
  61 # Boot Section Size in *bytes*
  62 #   Teensy halfKay   512
  63 #   Teensy++ halfKay 1024
  64 #   Atmel DFU loader 4096       for TMK Converter rev.1/rev.2
  65 #   LUFA bootloader  4096
  66 #   USBaspLoader     2048
  67 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  68
  69
  70 # Build Options
  71 #   comment out to disable the options.
  72 #
  73 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  74 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  75 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  76 CONSOLE_ENABLE = yes    # Console for debug(+400)
  77 COMMAND_ENABLE = yes    # Commands for debug and configuration
  78 #UNIMAP_ENABLE = yes
  79 #ACTIONMAP_ENABLE = yes         # Use 16bit actionmap instead of 8bit keymap
  80 #KEYMAP_SECTION_ENABLE = yes    # fixed address keymap for keymap editor
  81
  82
  83 #
  84 # Keymap file
  85 #
  86 ifeq (yes,$(strip $(UNIMAP_ENABLE)))
  87     KEYMAP_FILE = unimap
  88 else
  89     ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
  90         KEYMAP_FILE = actionmap
  91     else
  92         KEYMAP_FILE = keymap
  93     endif
  94 endif
  95 ifdef KEYMAP
  96     SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
  97 else
  98     SRC := $(KEYMAP_FILE).c $(SRC)
  99 endif
 100
 101
 102 # Search Path
 103 VPATH += $(TARGET_DIR)
 104 VPATH += $(TMK_DIR)
 105
 106 include $(TMK_DIR)/protocol/lufa.mk
 107 include $(TMK_DIR)/protocol.mk
 108 include $(TMK_DIR)/common.mk
 109 include $(TMK_DIR)/rules.mk