converter/m0110_usb/Makefile

   1 # Target file name (without extension).
   2 TARGET ?= m0110_usb
   3
   4 # Directory common source filess exist
   5 TMK_DIR ?= ../../tmk_core
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR ?= .
   9
  10 # keyboard dependent files
  11 SRC ?=  matrix.c \
  12         led.c \
  13         m0110.c
  14
  15 #
  16 # Keymap file
  17 #
  18 ifdef UNIMAP_ENABLE
  19     KEYMAP_FILE = unimap
  20 else
  21     ifdef ACTIONMAP_ENABLE
  22         KEYMAP_FILE = actionmap
  23     else
  24         KEYMAP_FILE = keymap
  25     endif
  26 endif
  27 ifdef KEYMAP
  28     SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
  29 else
  30     SRC := $(KEYMAP_FILE).c $(SRC)
  31 endif
  32
  33 CONFIG_H ?= config.h
  34
  35
  36 # MCU name, you MUST set this to match the board you are using
  37 # type "make clean" after changing this, so all files will be rebuilt
  38 MCU ?= atmega32u2
  39
  40
  41 # Processor frequency.
  42 #   Normally the first thing your program should do is set the clock prescaler,
  43 #   so your program will run at the correct speed.  You should also set this
  44 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  45 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  46 F_CPU ?= 16000000
  47
  48
  49 #
  50 # LUFA specific
  51 #
  52 # Target architecture (see library "Board Types" documentation).
  53 ARCH ?= AVR8
  54
  55 # Input clock frequency.
  56 #     This will define a symbol, F_USB, in all source code files equal to the
  57 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  58 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  59 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  60 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  61 #     at the end, this will be done automatically to create a 32-bit value in your
  62 #     source code.
  63 #
  64 #     If no clock division is performed on the input clock inside the AVR (via the
  65 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  66 F_USB ?= $(F_CPU)
  67
  68 # Interrupt driven control endpoint task
  69 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  70
  71
  72 # Boot Section Size in bytes
  73 #   Teensy halfKay   512
  74 #   Atmel DFU loader 4096
  75 #   LUFA bootloader  4096
  76 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  77
  78
  79 # Build Options
  80 #   *Comment out* to disable the options.
  81 #
  82 #BOOTMAGIC_ENABLE ?= yes        # Virtual DIP switch configuration(+1000)
  83 MOUSEKEY_ENABLE ?= yes  # Mouse keys(+4700)
  84 EXTRAKEY_ENABLE ?= yes  # Audio control and System control(+450)
  85 CONSOLE_ENABLE ?= yes   # Console for debug(+400)
  86 COMMAND_ENABLE ?= yes    # Commands for debug and configuration
  87 #SLEEP_LED_ENABLE ?= yes  # Breathing sleep LED during USB suspend
  88 #NKRO_ENABLE ?= yes     # USB Nkey Rollover
  89 #KEYMAP_SECTION_ENABLE ?= yes   # fixed address keymap for keymap editor
  90
  91
  92
  93 #---------------- Programming Options --------------------------
  94 PROGRAM_CMD ?= teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
  95
  96
  97 # Search Path
  98 VPATH += $(TARGET_DIR)
  99 VPATH += $(TMK_DIR)
 100
 101
 102 include $(TMK_DIR)/protocol/lufa.mk
 103 include $(TMK_DIR)/protocol.mk
 104 include $(TMK_DIR)/common.mk
 105 include $(TMK_DIR)/rules.mk