keyboard/tv44/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 ifdef TARGETFILE
  43         TARGET = $(TARGETFILE)
  44 else
  45         TARGET = tv44_lufa
  46 endif
  47
  48 ifdef LEDCONF
  49         LED = $(LEDCONF).c
  50 else
  51         LED = led.c
  52 endif
  53
  54 # Directory common source filess exist
  55 TMK_DIR = ../../tmk_core
  56
  57 # Directory keyboard dependent files exist
  58 TARGET_DIR = .
  59
  60 # project specific files
  61 SRC =   keymap_common.c \
  62         matrix.c \
  63         $(LED)
  64
  65 ifdef KEYMAP
  66     SRC := keymap_$(KEYMAP).c $(SRC)
  67 else
  68     SRC := keymap_tv44.c $(SRC)
  69 endif
  70
  71 CONFIG_H = config.h
  72
  73
  74 # MCU name
  75 #MCU = at90usb1287
  76 MCU = atmega32u4
  77
  78 # Processor frequency.
  79 #     This will define a symbol, F_CPU, in all source code files equal to the
  80 #     processor frequency in Hz. You can then use this symbol in your source code to
  81 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  82 #     automatically to create a 32-bit value in your source code.
  83 #
  84 #     This will be an integer division of F_USB below, as it is sourced by
  85 #     F_USB after it has run through any CPU prescalers. Note that this value
  86 #     does not *change* the processor frequency - it should merely be updated to
  87 #     reflect the processor speed set externally so that the code can use accurate
  88 #     software delays.
  89 F_CPU = 16000000
  90
  91
  92 #
  93 # LUFA specific
  94 #
  95 # Target architecture (see library "Board Types" documentation).
  96 ARCH = AVR8
  97
  98 # Input clock frequency.
  99 #     This will define a symbol, F_USB, in all source code files equal to the
 100 #     input clock frequency (before any prescaling is performed) in Hz. This value may
 101 #     differ from F_CPU if prescaling is used on the latter, and is required as the
 102 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
 103 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
 104 #     at the end, this will be done automatically to create a 32-bit value in your
 105 #     source code.
 106 #
 107 #     If no clock division is performed on the input clock inside the AVR (via the
 108 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 109 F_USB = $(F_CPU)
 110
 111 # Interrupt driven control endpoint task(+60)
 112 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 113
 114
 115 # Boot Section Size in *bytes*
 116 #   Teensy halfKay   512
 117 #   Teensy++ halfKay 1024
 118 #   Atmel DFU loader 4096
 119 #   LUFA bootloader  4096
 120 #   USBaspLoader     2048
 121 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 122
 123
 124 # Build Options
 125 #   comment out to disable the options.
 126 #
 127 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
 128 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
 129 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
 130 CONSOLE_ENABLE = yes    # Console for debug(+400)
 131 COMMAND_ENABLE = yes    # Commands for debug and configuration
 132 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
 133 NKRO_ENABLE = yes       # USB Nkey Rollover - not yet supported in LUFA
 134
 135
 136 # Optimize size but this may cause error "relocation truncated to fit"
 137 #EXTRALDFLAGS = -Wl,--relax
 138
 139 # Search Path
 140 VPATH += $(TARGET_DIR)
 141 VPATH += $(TMK_DIR)
 142
 143 include $(TMK_DIR)/protocol/lufa.mk
 144 include $(TMK_DIR)/common.mk
 145 include $(TMK_DIR)/rules.mk