converter/ps2_usb/Makefile

   1 # Target file name (without extension).
   2 TARGET = ps2_usb_lufa
   3
   4 # Directory common source filess exist
   5 TOP_DIR = ../..
   6
   7 # Directory keyboard dependent files exist
   8 TARGET_DIR = .
   9
  10 # project specific files
  11 SRC =   keymap_common.c \
  12         matrix.c \
  13         led.c
  14
  15 ifdef KEYMAP
  16     SRC := keymap_$(KEYMAP).c $(SRC)
  17 else
  18     SRC := keymap_plain.c $(SRC)
  19 endif
  20
  21 CONFIG_H = config.h
  22
  23
  24 # MCU name
  25 #MCU = at90usb1287
  26 MCU = atmega32u4
  27
  28 # Processor frequency.
  29 #     This will define a symbol, F_CPU, in all source code files equal to the
  30 #     processor frequency in Hz. You can then use this symbol in your source code to
  31 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  32 #     automatically to create a 32-bit value in your source code.
  33 #
  34 #     This will be an integer division of F_USB below, as it is sourced by
  35 #     F_USB after it has run through any CPU prescalers. Note that this value
  36 #     does not *change* the processor frequency - it should merely be updated to
  37 #     reflect the processor speed set externally so that the code can use accurate
  38 #     software delays.
  39 F_CPU = 16000000
  40
  41
  42 #
  43 # LUFA specific
  44 #
  45 # Target architecture (see library "Board Types" documentation).
  46 ARCH = AVR8
  47
  48 # Input clock frequency.
  49 #     This will define a symbol, F_USB, in all source code files equal to the
  50 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  51 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  52 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  53 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  54 #     at the end, this will be done automatically to create a 32-bit value in your
  55 #     source code.
  56 #
  57 #     If no clock division is performed on the input clock inside the AVR (via the
  58 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  59 F_USB = $(F_CPU)
  60
  61 # Interrupt driven control endpoint task(+60)
  62 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  63
  64
  65 # Boot Section Size in *bytes*
  66 #   Teensy halfKay   512
  67 #   Teensy++ halfKay 1024
  68 #   Atmel DFU loader 4096
  69 #   LUFA bootloader  4096
  70 #   USBaspLoader     2048
  71 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  72
  73
  74 # Build Options
  75 #   comment out to disable the options.
  76 #
  77 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  78 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  79 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  80 CONSOLE_ENABLE = yes    # Console for debug(+400)
  81 COMMAND_ENABLE = yes    # Commands for debug and configuration
  82 NKRO_ENABLE = yes       # USB Nkey Rollover - not yet supported in LUFA
  83
  84
  85 # PS/2 Options
  86 #
  87 PS2_USE_USART = yes     # uses hardware USART engine for PS/2 signal receive(recomened)
  88 #PS2_USE_INT = yes      # uses external interrupt for falling edge of PS/2 clock pin
  89 #PS2_USE_BUSYWAIT = yes # uses primitive reference code
  90
  91
  92 # Optimize size but this may cause error "relocation truncated to fit"
  93 #EXTRALDFLAGS = -Wl,--relax
  94
  95 # Search Path
  96 VPATH += $(TARGET_DIR)
  97 VPATH += $(TOP_DIR)
  98
  99 include $(TOP_DIR)/protocol.mk
 100 include $(TOP_DIR)/protocol/lufa.mk
 101 include $(TOP_DIR)/common.mk
 102 include $(TOP_DIR)/rules.mk