converter/x68k_usb/Makefile

   1 #
   2 # Makefile for PJRC Teensy
   3 #
   4
   5
   6 # Target file name (without extension).
   7 TARGET = x68k_usb_pjrc
   8
   9 # Directory common source filess exist
  10 TMK_DIR = ../../tmk_core
  11
  12 # Directory keyboard dependent files exist
  13 TARGET_DIR = .
  14
  15 # keyboard dependent files
  16 SRC =   keymap.c \
  17         matrix.c \
  18         led.c \
  19         protocol/serial_uart.c
  20
  21 CONFIG_H = config_pjrc.h
  22
  23
  24 # MCU name, you MUST set this to match the board you are using
  25 # type "make clean" after changing this, so all files will be rebuilt
  26 #MCU = at90usb162       # Teensy 1.0
  27 MCU = atmega32u4       # Teensy 2.0
  28 #MCU = at90usb646       # Teensy++ 1.0
  29 #MCU = at90usb1286      # Teensy++ 2.0
  30
  31
  32 # Processor frequency.
  33 #   Normally the first thing your program should do is set the clock prescaler,
  34 #   so your program will run at the correct speed.  You should also set this
  35 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  36 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  37 F_CPU = 16000000
  38
  39
  40 # Boot Section Size in bytes
  41 #   Teensy halfKay   512
  42 #   Atmel DFU loader 4096
  43 #   LUFA bootloader  4096
  44 OPT_DEFS += -DBOOTLOADER_SIZE=4096
  45
  46
  47 # Build Options
  48 #   *Comment out* to disable the options.
  49 #
  50 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
  51 MOUSEKEY_ENABLE = yes   # Mouse keys(+4700)
  52 EXTRAKEY_ENABLE = yes   # Audio control and System control(+450)
  53 CONSOLE_ENABLE = yes    # Console for debug(+400)
  54 COMMAND_ENABLE = yes    # Commands for debug and configuration
  55 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
  56 #NKRO_ENABLE = yes      # USB Nkey Rollover - not yet supported in LUFA
  57
  58
  59
  60 #---------------- Programming Options --------------------------
  61 AVRDUDE = avrdude
  62 # Type: avrdude -c ? to get a full listing.
  63 AVRDUDE_PROGRAMMER = avr109
  64 AVRDUDE_PORT = /dev/ttyACM0
  65 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
  66 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
  67
  68 # Uncomment the following if you want avrdude's erase cycle counter.
  69 # Note that this counter needs to be initialized first using -Yn,
  70 # see avrdude manual.
  71 #AVRDUDE_ERASE_COUNTER = -y
  72
  73 # Uncomment the following if you do /not/ wish a verification to be
  74 # performed after programming the device.
  75 #AVRDUDE_NO_VERIFY = -V
  76
  77 # Increase verbosity level.  Please use this when submitting bug
  78 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
  79 # to submit bug reports.
  80 #AVRDUDE_VERBOSE = -v -v
  81
  82 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
  83 #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
  84 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
  85 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
  86 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
  87
  88 #PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
  89 #PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
  90 PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
  91
  92
  93 # Search Path
  94 VPATH += $(TARGET_DIR)
  95 VPATH += $(TMK_DIR)
  96
  97
  98 include $(TMK_DIR)/protocol/pjrc.mk
  99 include $(TMK_DIR)/protocol.mk
 100 include $(TMK_DIR)/common.mk
 101 include $(TMK_DIR)/rules.mk