Merge pull request #81 from bgould/master
[tmk_keyboard.git] / converter / terminal_bluefruit / Makefile
1 # Target file name (without extension).
2 TARGET = terminal_bluefruit
3
4 # Directory common source filess exist
5 TOP_DIR = ../..
6
7 # Directory keyboard dependent files exist
8 TARGET_DIR = .
9
10 # keyboard dependent files
11 SRC = keymap.c \
12 matrix.c \
13 led.c
14
15 CONFIG_H = config.h
16
17 BLUEFRUIT_TRACE_SERIAL=true
18
19 # MCU name, you MUST set this to match the board you are using
20 # type "make clean" after changing this, so all files will be rebuilt
21 #MCU = at90usb162 # Teensy 1.0
22 MCU = atmega32u4 # Teensy 2.0
23 #MCU = at90usb646 # Teensy++ 1.0
24 #MCU = at90usb1286 # Teensy++ 2.0
25
26
27 # Processor frequency.
28 # Normally the first thing your program should do is set the clock prescaler,
29 # so your program will run at the correct speed. You should also set this
30 # variable to same clock speed. The _delay_ms() macro uses this, and many
31 # examples use this variable to calculate timings. Do not add a "UL" here.
32 F_CPU = 16000000
33
34
35 #
36 # LUFA specific
37 #
38 # Target architecture (see library "Board Types" documentation).
39 ARCH = AVR8
40
41 # Input clock frequency.
42 # This will define a symbol, F_USB, in all source code files equal to the
43 # input clock frequency (before any prescaling is performed) in Hz. This value may
44 # differ from F_CPU if prescaling is used on the latter, and is required as the
45 # raw input clock is fed directly to the PLL sections of the AVR for high speed
46 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
47 # at the end, this will be done automatically to create a 32-bit value in your
48 # source code.
49 #
50 # If no clock division is performed on the input clock inside the AVR (via the
51 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
52 F_USB = $(F_CPU)
53
54 # Interrupt driven control endpoint task
55 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
56
57
58 # Boot Section Size in bytes
59 # Teensy halfKay 512
60 # Atmel DFU loader 4096
61 # LUFA bootloader 4096
62 OPT_DEFS += -DBOOTLOADER_SIZE=4096
63
64
65 # Build Options
66 # comment out to disable the options.
67 #
68 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
69 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
70 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
71 CONSOLE_ENABLE = yes # Console for debug(+400)
72 COMMAND_ENABLE = yes # Commands for debug and configuration
73 #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
74 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
75
76
77 #
78 # PS/2 protocol implementations
79 # USART is recommended if it is available, others are for reference purpose.
80 # INT implementation will drop simultaneous key strokes.
81 #
82 #PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
83 PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
84 #PS2_USE_BUSYWAIT = yes # uses primitive reference code
85
86 ifdef PS2_USE_USART
87 SRC += protocol/ps2_usart.c
88 OPT_DEFS += -DPS2_USE_USART
89 endif
90
91 ifdef PS2_USE_INT
92 SRC += protocol/ps2.c
93 OPT_DEFS += -DPS2_USE_INT
94 endif
95
96 ifdef PS2_USE_BUSYWAIT
97 SRC += protocol/ps2.c
98 OPT_DEFS += -DPS2_USE_BUSYWAIT
99 endif
100
101 #---------------- Programming Options --------------------------
102 PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
103
104
105 # Search Path
106 VPATH += $(TARGET_DIR)
107 VPATH += $(TOP_DIR)
108
109
110 include $(TOP_DIR)/protocol/bluefruit.mk
111 include $(TOP_DIR)/protocol.mk
112 include $(TOP_DIR)/common.mk
113 include $(TOP_DIR)/rules.mk
Imprint / Impressum