Memo of deveopment ================== just memo, NOT WORTH READING Bug: - Factory Reset PIO4 doesn't work - the reason is unclear - 12/08 NOT LOOK INTO ANY MORE - WORKAROUND: use serial pins(3.3V, GND, RX and TX) - SF,1 and R,1 to set factory defalult Todo: - LED cover and switch knob and new Slide Switch - RN42 auto configuration - configure the module as HID device every time powering up - this'll reduce work load of assembly - move rn42 to protocol directory when it becomes reusable stack - sendchar() in lufa.c no buffer - no buffering. character lost can be caused. - LUFA sendchar should be buffered and serial_uart.c buffur size is too large(256). - BT operations - disconnect - new connection - remove connection - sendchar() in lufa.c block loop - DONE 11/29 - block loop when powered with AC adapter - FrameNumber is not updated when adapter powered Improving: - ADC resolution AVR120 AVR32138 - Enhancing ADC resolution by oversampling AVR121 http://www.atmel.com/images/doc8003.pdf - disable digital input buffer DIDR(7.8.6) Design: - suspend.h - DONE 11/26 - remove argument from suspend_power_down() for backward compatitibility - remove MCU dependent power saving code from core/keyboard - DONE 11/23 - it should be located in project matrix.c - HHKB matrix.c needs matrix_prev? - is_modified() is obsolete now. really needs? - ADC: removing AREF capacitor C10 - seems to be better while usb powered - still bad while battery powered http://electronics.stackexchange.com/questions/105849/avcc-and-capacitor-using-adc - ADC: smaller resistors for voltage dividor - 1K + 1K: not improved. - 11/27 LUFA: USB connection check: state of USB deivce - USB_DeviceState: USB_Deivce_State_t { Unattached, Powered, Default, Addressed, Configured*, Suspended* } Unattached: unpluged Powered: pluged with power adapter Default: enumerate process bigin Addressed: addressed Configured: enumerated Suspended: suspended - USB_IsInitialized: state of LUFA core setup becomes true in USB_Init() USBController_AVR8.c becomes false in USB_Disable() USBController_AVR8.c - USB_VBUS_GetStatus(): state of VBUS(power/connection) - USB_Disable() detaches, disables all interrupts, controller, PLL, regulater. - When connect to power adapter - event happened: CW or CSW or C or DDC - USB state: not configured - USB evnets - USB connect: CSWRWRW - USB connect but fail to enumeration: CWRWRWRWS - USB disconnect: D - Power adapter connect: CW, CSW, C - Power adapter disconnect: D Power saving: - Pro2 current consumption - active: 138.2mA(no device on Hub) - suspended: 30.9mA(WakeUp enabled DIPSW6) - suspended: 0mA->46.0mA(WakeUp disabled DIPSW6) - Pro current consumption - active: 54.0mA - suspended: 40.5mA(WakeUp enabled DIPSW6) - suspended: 0.3mA(WakeUp disabled DIPSW6) - RN42 3.3V - disconnected(Idle): 5mA (config mode) - connected(Active): SW,0000: 23-26mA SW,0010: 27-29mA worse than 0000 for unknown reason SW,0020: 17-19mA mouse NG SW,0030: 13-16mA laggy mouse NG SW,0050: 10-13mA laggy mouse NG - matrix power saving - power saving while externally powered and not while unpluged - confirm suspend mode lufa.c: matrix_power_*, suspend_wakeup_condition - 8MHz clock - When not connected in a few minutes get into deep sleep to save battery life - CTS is needed for waking up from deep sleep? How deep sleep is activated? - firmware controlled 3.3V DC converter to switch on/off BT module - sleep MCU and BT module(keyboard is not used) - deep sleep MCU and BT module(keyboard is not used for long time) - deep sleep MCU and turn off BT module(keyboard is not used and not connected) - Battery ADC; switching, high resistance - switching gnd end of divider with PF4 - high resistor 100K/1M? capacitor 10nF http://www.eevblog.com/forum/beginners/measuring-battery-voltage-without-consuming-current/ - During USB suspend change clock source to internal RC from external Xtal(6.8) - FRZCLK: you can freeze clock for power saving. still WAKEUPI and VBUSTI interrupts are available while freezing.(21.7.3) - Suspend: Clear Suspend Bit, Freeze clock, disable PLL, MCU sleep(21.13) - Voltage reference(8.1.1) - to reduce power consumption while power down mode - unset ADEN before sleep(24.7) Lipo ---- 850mA lasts around 9 hours(07/28) Sparkfun Polymer Lithium Ion Battery 850mAh: https://www.sparkfun.com/products/341 Lipo Cell spec: https://www.sparkfun.com/datasheets/Batteries/063048%20Li-polymer.pdf Protection spec: http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Prototyping/BatteryProtection.pdf min typical max over-charge 4.255 4.280 4.305 over-charge discover? 4.030 4.080 4.130 over-discharge 2.827 2.900 2.973 over-discharge discover 3.022 3.100 3.178 ADC voltage monitor: voltage divider 10K+10K(0.5) ADC=V*0.5/2.56*1024 V ADC ------------------ 4.20 0x347(839) 3.10 0x26b(619) TROUBLE SHOOT ------------- 07/16 After fix of voltage dividor on GPIO6, had a trouble that it could not send a char to BT module, though could receive. Found R8 had wrong 1K resistor and changed to 10K, after that it can send to the module again. Not sure how it had sent with the wrong 1K before. 07/18 On Linux, had an USB related trouble; keyobard or console didn't work for some reason. Changing PID cured this problem. Very annoying, took very long time before resolved it. 12/07 rn42_rts() read 1 every time. R12 broke in open mode(no coductive), idk why, too much heat with soldering? and PF1 pin was not soldered. It resolved with resoldering PF1 and new resistor on R12. Done: - low battery alert(solid light) 09/04 - *** Rev.E BT test *** - DONE - with MCP73832, new Schottky, tantalum caps - DONE 12/07 * MCP73832 doesn't leak from Vcc pin when unpluged and battery powered 34mV vs 2.07V(MCP73831) at Vcc pin MCP73832 doesn't need revese protection diode D5 * PMEG2010ER is very low VF while reverse current/voltage is high VF=0.96 vs 1.98(RB160M-30TR)with Fluke 175 Anode of D11 is 680mV vs 20mV(RB160M-30TR) 780mV is still low < 1.4V VBUS plugin detection(21.11) this doesn't cause false VBUS detect and 780mV on MCP73832 Vcc pin is also no problem. D5 can be removed. - ADC divider switching - DONE 12/07 * Drain and Source of Q4 Pch was reversed wrongly on Rev.E. - reverse current from Lipo charger - DONE 12/07 * MCP73832 has no recverse current from Vcc pin unlike MCP73831 - Rev.F design - DONE - current measure point - DONE 12/08 - change value of cap 68->47 - DONE 12/08 - PPTC land pattern: no solder jumper, use 0Ohm resistor instead - CANCEL 12/08 - Q4 Pch FET: wrong Drain and Source - DONE 12/08 - D5 can be removed. - DONE 12/08 - BT_INDICATOR LED turns on wrongly when touching line or pin. -- pull-up enabled on PF6/GPIO2 08/30 - Lipo charger configuration: fast charge time: USB charger spec? -- used 2kohm - use LED of charger to alarm low battery. LED should be powered directly from Lipo? - cancel; powered from VUSB - Use RTS in serial_uart.c to resolve missing chars from help message of RN-42 - done - CTS/RTS lines are needed? just connect in loop back if no flow control is needed. - done - add IO pin to charger status CHRG; LED control(low) and detect charge status(input HiZ) 07.24 - LINKED: add trace on PIO2 to PF6 07.24 - Lipo voltage ADC sensing - Lipo charger MCP73831: needs capacitor 4.7uF *2 - USB connection check - 07.01 - BT on/off check: whether RX line is pulled up? - checking RTS 07.01 - USB/BT switching BT is on -> BT, BT is off -> USB - 07.01 - Under voltage lock out UVLO for protection of Lipo - Lipo has discharge protection at 3.100V 07.01 - Power saving: HHKB scan, BT radio control - 9h with 850mAh, this is enough 07.01 - Power selector doesn't work; Q4 MOSFET leaks from Lipo to USB power line. -- use Schottky instead 07/04 - wrongly suspended when powered from adapter without USB connection - DONE - suspend event may occur when plug into adapter - and never wake until conected to real USB line - without debug print via USB no problem; CSW(wake just after suspend as real USB line) - seems like USB print causes this problem after suspended - lose USB connection during power-down mode - DONE - USB initialize code in main() causes this - WRONG - Do not power-down during USB connection is active - DONE 11/11 (USB_DeviceState == USB_DEVICE_Configured) is used to check USB connection matrix_power_down() matrix.c - 11/23 - with Nexus5 keyboard and mouse are very laggy. Not confirmed. 01/15 - switch BT host connections - CANCEL 01/15 - switch next connection cannot switch connection with version 6.15 at least - When given power only from wall wart adapter - DONE? not confirmed 01/15 - it sleeps. it should not sleep - Configured state without USB connection? - timer is slow while power down - DONE 11/26 - time out interrupt is lost while power down? - interrupt of watchdog timer compensates timer counter(avr/suspend.c) - repeated CHARGING/FULL_CHARGED - No longer problem 01/15 - In LTC sharp pulses are observed. - MCP has no pulse but still has a problem. - needs more wait before read pin state? - NO - USB plug-in fails while BT - No longer problem 01/15 - it ends in suspend state - maybe, not responsive to host enumeration process due to power-down. - matrix_power_down() only when state is unattached - 11/26 - need to observe a while