/** ****************************************************************************** * @file stm32l0xx_hal_rtc.c * @author MCD Application Team * @version V1.2.0 * @date 06-February-2015 * @brief RTC HAL module driver. * This file provides firmware functions to manage the following * functionalities of the Real Time Clock (RTC) peripheral: * + Initialization/de-initialization functions * + I/O operation functions * + Peripheral Control functions * + Peripheral State functions * @verbatim ============================================================================== ##### Backup Domain Operating Condition ##### ============================================================================== [..] As long as the supply voltage remains in the operating range, the RTC never stops, regardless of the device status (Run mode, low power modes or under reset). ##### Backup Domain Reset ##### ================================================================== [..] The backup domain reset sets all RTC registers and the RCC_CSR register to their reset values. [..] A backup domain reset is generated when one of the following events occurs: (+) Software reset, triggered by setting the RTCRST bit in the RCC Control Status register (RCC_CSR). (+) Power reset (BOR/POR/PDR). ##### Backup Domain Access ##### ================================================================== [..] After reset, the backup domain (RTC registers and RTC backup data registers) is protected against possible unwanted write accesses. [..] To enable access to the RTC Domain and RTC registers, proceed as follows: (+) Enable the Power Controller (PWR) APB1 interface clock using the __HAL_RCC_PWR_CLK_ENABLE() function. (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. (+) Select the RTC clock source using the __HAL_RCC_RTC_CONFIG() function. (+) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() function. ##### How to use RTC Driver ##### =================================================================== [..] (+) Enable the RTC domain access (see description in the section above). (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour format using the HAL_RTC_Init() function. *** Time and Date configuration *** =================================== [..] (+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime() and HAL_RTC_SetDate() functions. (+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions. *** Alarm configuration *** =========================== [..] (+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function. You can also configure the RTC Alarm with interrupt mode using the HAL_RTC_SetAlarm_IT() function. (+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function. *** RTC Wakeup configuration *** ================================ [..] (+) To configure the RTC Wakeup Clock source and Counter use the HAL_RTC_SetWakeUpTimer() function. You can also configure the RTC Wakeup timer with interrupt mode using the HAL_RTC_SetWakeUpTimer_IT() function. (+) To read the RTC WakeUp Counter register, use the HAL_RTC_GetWakeUpTimer() function. *** Outputs configuration *** ============================= [..] The RTC has 2 different outputs: (+) RTC_ALARM: this output is used to manage the RTC Alarm A, Alarm B and WaKeUp signals. To output the selected RTC signal, use the HAL_RTC_Init() function. (+) RTC_CALIB: this output is 512Hz signal or 1Hz. To enable the RTC_CALIB, use the HAL_RTCEx_SetCalibrationOutPut() function. (+) Two pins can be used as RTC_ALARM or RTC_CALIB (PC13, PB14) managed on the RTC_OR register. (+) When the RTC_CALIB or RTC_ALARM output is selected, the RTC_OUT pin is automatically configured in output alternate function. *** Smooth digital Calibration configuration *** ================================================ [..] (+) Configure the RTC Original Digital Calibration Value and the corresponding calibration cycle period (32s,16s and 8s) using the HAL_RTCEx_SetSmoothCalib() function. *** TimeStamp configuration *** =============================== [..] (+) Enables the RTC TimeStamp using the HAL_RTC_SetTimeStamp() function. You can also configure the RTC TimeStamp with interrupt mode using the HAL_RTC_SetTimeStamp_IT() function. (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTC_GetTimeStamp() function. *** Tamper configuration *** ============================ [..] (+) Enable the RTC Tamper and Configure the Tamper filter count, trigger Edge or Level according to the Tamper filter (if equal to 0 Edge else Level) value, sampling frequency, NoErase, MaskFlag, precharge or discharge and Pull-UP using the HAL_RTC_SetTamper() function. You can configure RTC Tamper with interrupt mode using HAL_RTC_SetTamper_IT() function. (+) The default configuration of the Tamper erases the backup registers. To avoid erase, enable the NoErase field on the RTC_TAMPCR register. *** Backup Data Registers configuration *** =========================================== [..] (+) To write to the RTC Backup Data registers, use the HAL_RTC_BKUPWrite() function. (+) To read the RTC Backup Data registers, use the HAL_RTC_BKUPRead() function. (+) The backup registers are reset when a tamper detection event occurs ##### RTC and low power modes ##### ================================================================== [..] The MCU can be woken up from a low power mode by an RTC alternate function. [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B), RTC wakeup, RTC tamper event detection and RTC time stamp event detection. These RTC alternate functions can wake up the system from the Stop and Standby low power modes. [..] The system can also wake up from low power modes without depending on an external interrupt (Auto-wakeup mode), by using the RTC alarm or the RTC wakeup events. [..] The RTC provides a programmable time base for waking up from the Stop or Standby mode at regular intervals. Wakeup from STOP and Standby modes is possible only when the RTC clock source is LSE or LSI. @endverbatim ****************************************************************************** * @attention * *

© COPYRIGHT(c) 2015 STMicroelectronics

* * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32l0xx_hal.h" /** @addtogroup STM32L0xx_HAL_Driver * @{ */ /** @addtogroup RTC * @brief RTC HAL module driver * @{ */ #ifdef HAL_RTC_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ /* Exported functions --------------------------------------------------------*/ /** @addtogroup RTC_Exported_Functions * @{ */ /** @addtogroup RTC_Exported_Functions_Group1 * @brief Initialization and Configuration functions * @verbatim =============================================================================== ##### Initialization and de-initialization functions ##### =============================================================================== [..] This section provides functions allowing to initialize and configure the RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable RTC registers Write protection, enter and exit the RTC initialization mode, RTC registers synchronization check and reference clock detection enable. (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base. It is split into 2 programmable prescalers to minimize power consumption. (++) A 7-bit asynchronous prescaler and a 15-bit synchronous prescaler. (++) When both prescalers are used, it is recommended to configure the asynchronous prescaler to a high value to minimize power consumption. (#) All RTC registers are Write protected. Writing to the RTC registers is enabled by writing a key into the Write Protection register, RTC_WPR. (#) To configure the RTC Calendar, user application should enter initialization mode. In this mode, the calendar counter is stopped and its value can be updated. When the initialization sequence is complete, the calendar restarts counting after 4 RTCCLK cycles. (#) To read the calendar through the shadow registers after Calendar initialization, calendar update or after wakeup from low power modes the software must first clear the RSF flag. The software must then wait until it is set again before reading the calendar, which means that the calendar registers have been correctly copied into the RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function implements the above software sequence (RSF clear and RSF check). @endverbatim * @{ */ /** * @brief Initializes the RTC peripheral * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc) { /* Check the RTC peripheral state */ if(hrtc == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_RTC_ALL_INSTANCE(hrtc->Instance)); assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat)); assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv)); assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv)); assert_param(IS_RTC_OUTPUT(hrtc->Init.OutPut)); assert_param(IS_RTC_OUTPUT_REMAP(hrtc->Init.OutPutRemap)); assert_param(IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity)); assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType)); if(hrtc->State == HAL_RTC_STATE_RESET) { /* Initialize RTC MSP */ HAL_RTC_MspInit(hrtc); } /* Set RTC state */ hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set Initialization mode */ if(RTC_EnterInitMode(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state */ hrtc->State = HAL_RTC_STATE_ERROR; return HAL_ERROR; } else { /* Clear RTC_CR FMT, OSEL and POL Bits */ hrtc->Instance->CR &= ((uint32_t)~(RTC_CR_FMT | RTC_CR_OSEL | RTC_CR_POL)); /* Set RTC_CR register */ hrtc->Instance->CR |= (uint32_t)(hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity); /* Configure the RTC PRER */ hrtc->Instance->PRER = (uint32_t)(hrtc->Init.SynchPrediv); hrtc->Instance->PRER |= (uint32_t)(hrtc->Init.AsynchPrediv << 16); /* Exit Initialization mode */ hrtc->Instance->ISR &= ((uint32_t)~RTC_ISR_INIT); hrtc->Instance->OR &= (uint32_t)~(RTC_OR_ALARMOUTTYPE | RTC_OR_OUT_RMP); hrtc->Instance->OR |= (uint32_t)(hrtc->Init.OutPutType | hrtc->Init.OutPutRemap); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } } /** * @brief DeInitializes the RTC peripheral * @param hrtc: RTC handle * @note This function doesn't reset the RTC Backup Data registers. * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc) { uint32_t tickstart = 0; /* Check the parameters */ assert_param(IS_RTC_ALL_INSTANCE(hrtc->Instance)); /* Set RTC state */ hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set Initialization mode */ if(RTC_EnterInitMode(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state */ hrtc->State = HAL_RTC_STATE_ERROR; return HAL_ERROR; } else { /* Reset TR, DR and CR registers */ hrtc->Instance->TR = (uint32_t)0x00000000; hrtc->Instance->DR = ((uint32_t)(RTC_DR_WDU_0 | RTC_DR_MU_0 | RTC_DR_DU_0)); /* Reset All CR bits except CR[2:0] */ hrtc->Instance->CR &= RTC_CR_WUCKSEL; tickstart = HAL_GetTick(); /* Wait till WUTWF flag is set and if Time out is reached exit */ while(((hrtc->Instance->ISR) & RTC_ISR_WUTWF) == (uint32_t)RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state */ hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } /* Reset all RTC CR register bits */ hrtc->Instance->CR &= (uint32_t)0x00000000; hrtc->Instance->WUTR = RTC_WUTR_WUT; hrtc->Instance->PRER = ((uint32_t)(RTC_PRER_PREDIV_A | 0x000000FF)); hrtc->Instance->ALRMAR = (uint32_t)0x00000000; hrtc->Instance->ALRMBR = (uint32_t)0x00000000; hrtc->Instance->SHIFTR = (uint32_t)0x00000000; hrtc->Instance->CALR = (uint32_t)0x00000000; hrtc->Instance->ALRMASSR = (uint32_t)0x00000000; hrtc->Instance->ALRMBSSR = (uint32_t)0x00000000; /* Reset ISR register and exit initialization mode */ hrtc->Instance->ISR = (uint32_t)0x00000000; /* Reset Tamper configuration register */ hrtc->Instance->TAMPCR = 0x00000000; /* Reset Option register */ hrtc->Instance->OR = 0x00000000; /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) { if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_ERROR; return HAL_ERROR; } } } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* De-Initialize RTC MSP */ HAL_RTC_MspDeInit(hrtc); hrtc->State = HAL_RTC_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Initializes the RTC MSP. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTC_MspInit could be implenetd in the user file */ } /** * @brief DeInitializes the RTC MSP. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTC_MspDeInit could be implenetd in the user file */ } /** * @} */ /** @addtogroup RTC_Exported_Functions_Group2 * @brief RTC Time and Date functions * @verbatim =============================================================================== ##### RTC Time and Date functions ##### =============================================================================== [..] This section provide functions allowing to configure Time and Date features @endverbatim * @{ */ /** * @brief Sets RTC current time. * @param hrtc: RTC handle * @param sTime: Pointer to Time structure * @param Format: Specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving)); assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; if(Format == RTC_FORMAT_BIN) { if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) { assert_param(IS_RTC_HOUR12(sTime->Hours)); assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat)); } else { sTime->TimeFormat = 0x00; assert_param(IS_RTC_HOUR24(sTime->Hours)); } assert_param(IS_RTC_MINUTES(sTime->Minutes)); assert_param(IS_RTC_SECONDS(sTime->Seconds)); tmpreg = (uint32_t)(((uint32_t)RTC_ByteToBcd2(sTime->Hours) << 16) | \ ((uint32_t)RTC_ByteToBcd2(sTime->Minutes) << 8) | \ ((uint32_t)RTC_ByteToBcd2(sTime->Seconds)) | \ (((uint32_t)sTime->TimeFormat) << 16)); } else { if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) { tmpreg = RTC_Bcd2ToByte(sTime->Hours); assert_param(IS_RTC_HOUR12(tmpreg)); assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat)); } else { sTime->TimeFormat = 0x00; assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours))); } assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes))); assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds))); tmpreg = (((uint32_t)(sTime->Hours) << 16) | \ ((uint32_t)(sTime->Minutes) << 8) | \ ((uint32_t)sTime->Seconds) | \ ((uint32_t)(sTime->TimeFormat) << 16)); } UNUSED(tmpreg); /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set Initialization mode */ if(RTC_EnterInitMode(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state */ hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } else { /* Set the RTC_TR register */ hrtc->Instance->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK); /* Clear the bits to be configured */ hrtc->Instance->CR &= ((uint32_t)~RTC_CR_BCK); /* Configure the RTC_CR register */ hrtc->Instance->CR |= (uint32_t)(sTime->DayLightSaving | sTime->StoreOperation); /* Exit Initialization mode */ hrtc->Instance->ISR &= ((uint32_t)~RTC_ISR_INIT); /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) { if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; __HAL_UNLOCK(hrtc); return HAL_OK; } } /** * @brief Gets RTC current time. * @param hrtc: RTC handle * @param sTime: Pointer to Time structure * @param Format: Specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values in the * higher-order calendar shadow registers. * Reading RTC current time locks the values in calendar shadow registers until current * date is read to ensure consistency between the time and date values. * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); /* Get subseconds values from the correspondent registers*/ sTime->SubSeconds = (uint32_t)(hrtc->Instance->SSR); /* Get the TR register */ tmpreg = (uint32_t)(hrtc->Instance->TR & RTC_TR_RESERVED_MASK); /* Fill the structure fields with the read parameters */ sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> 16); sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >>8); sTime->Seconds = (uint8_t)(tmpreg & (RTC_TR_ST | RTC_TR_SU)); sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> 16); /* Check the input parameters format */ if(Format == RTC_FORMAT_BIN) { /* Convert the time structure parameters to Binary format */ sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours); sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes); sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds); } return HAL_OK; } /** * @brief Sets RTC current date. * @param hrtc: RTC handle * @param sDate: Pointer to date structure * @param Format: specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format) { uint32_t datetmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; if((Format == RTC_FORMAT_BIN) && ((sDate->Month & 0x10) == 0x10)) { sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10)) + (uint8_t)0x0A); } assert_param(IS_RTC_WEEKDAY(sDate->WeekDay)); if(Format == RTC_FORMAT_BIN) { assert_param(IS_RTC_YEAR(sDate->Year)); assert_param(IS_RTC_MONTH(sDate->Month)); assert_param(IS_RTC_DATE(sDate->Date)); datetmpreg = (((uint32_t)RTC_ByteToBcd2(sDate->Year) << 16) | \ ((uint32_t)RTC_ByteToBcd2(sDate->Month) << 8) | \ ((uint32_t)RTC_ByteToBcd2(sDate->Date)) | \ ((uint32_t)sDate->WeekDay << 13)); } else { assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(sDate->Year))); datetmpreg = RTC_Bcd2ToByte(sDate->Month); assert_param(IS_RTC_MONTH(datetmpreg)); datetmpreg = RTC_Bcd2ToByte(sDate->Date); assert_param(IS_RTC_DATE(datetmpreg)); datetmpreg = ((((uint32_t)sDate->Year) << 16) | \ (((uint32_t)sDate->Month) << 8) | \ ((uint32_t)sDate->Date) | \ (((uint32_t)sDate->WeekDay) << 13)); } /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set Initialization mode */ if(RTC_EnterInitMode(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state*/ hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } else { /* Set the RTC_DR register */ hrtc->Instance->DR = (uint32_t)(datetmpreg & RTC_DR_RESERVED_MASK); /* Exit Initialization mode */ hrtc->Instance->ISR &= ((uint32_t)~RTC_ISR_INIT); /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) { if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY ; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } } /** * @brief Gets RTC current date. * @param hrtc: RTC handle * @param sDate: Pointer to Date structure * @param Format: Specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format) { uint32_t datetmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); /* Get the DR register */ datetmpreg = (uint32_t)(hrtc->Instance->DR & RTC_DR_RESERVED_MASK); /* Fill the structure fields with the read parameters */ sDate->Year = (uint8_t)((datetmpreg & (RTC_DR_YT | RTC_DR_YU)) >> 16); sDate->Month = (uint8_t)((datetmpreg & (RTC_DR_MT | RTC_DR_MU)) >> 8); sDate->Date = (uint8_t)(datetmpreg & (RTC_DR_DT | RTC_DR_DU)); sDate->WeekDay = (uint8_t)((datetmpreg & (RTC_DR_WDU)) >> 13); /* Check the input parameters format */ if(Format == RTC_FORMAT_BIN) { /* Convert the date structure parameters to Binary format */ sDate->Year = (uint8_t)RTC_Bcd2ToByte(sDate->Year); sDate->Month = (uint8_t)RTC_Bcd2ToByte(sDate->Month); sDate->Date = (uint8_t)RTC_Bcd2ToByte(sDate->Date); } return HAL_OK; } /** * @} */ /** @addtogroup RTC_Exported_Functions_Group3 * @brief RTC Alarm functions * @verbatim =============================================================================== ##### RTC Alarm functions ##### =============================================================================== [..] This section provides functions allowing to configure Alarm feature @endverbatim * @{ */ /** * @brief Sets the specified RTC Alarm. * @param hrtc: RTC handle * @param sAlarm: Pointer to Alarm structure * @param Format: Specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format) { uint32_t tickstart = 0; uint32_t tmpreg = 0, subsecondtmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); assert_param(IS_RTC_ALARM(sAlarm->Alarm)); assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask)); assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel)); assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds)); assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; if(Format == RTC_FORMAT_BIN) { if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) { assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours)); assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); } else { sAlarm->AlarmTime.TimeFormat = 0x00; assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours)); } assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes)); assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds)); if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) { assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay)); } else { assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay)); } tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16) | \ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8) | \ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24) | \ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ ((uint32_t)sAlarm->AlarmMask)); } else { if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) { tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); assert_param(IS_RTC_HOUR12(tmpreg)); assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); } else { sAlarm->AlarmTime.TimeFormat = 0x00; assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); } assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes))); assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds))); if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) { tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg)); } else { tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg)); } tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16) | \ ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8) | \ ((uint32_t) sAlarm->AlarmTime.Seconds) | \ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \ ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24) | \ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ ((uint32_t)sAlarm->AlarmMask)); } /* Configure the Alarm A or Alarm B Sub Second registers */ subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask)); /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the Alarm register */ if(sAlarm->Alarm == RTC_ALARM_A) { /* Disable the Alarm A interrupt */ __HAL_RTC_ALARMA_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA); tickstart = HAL_GetTick(); /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } hrtc->Instance->ALRMAR = (uint32_t)tmpreg; /* Configure the Alarm A Sub Second register */ hrtc->Instance->ALRMASSR = subsecondtmpreg; /* Configure the Alarm state: Enable Alarm */ __HAL_RTC_ALARMA_ENABLE(hrtc); } else { /* Disable the Alarm B interrupt */ __HAL_RTC_ALARMB_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRB); tickstart = HAL_GetTick(); /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } hrtc->Instance->ALRMBR = (uint32_t)tmpreg; /* Configure the Alarm B Sub Second register */ hrtc->Instance->ALRMBSSR = subsecondtmpreg; /* Configure the Alarm state: Enable Alarm */ __HAL_RTC_ALARMB_ENABLE(hrtc); } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Sets the specified RTC Alarm with Interrupt * @param hrtc: RTC handle * @param sAlarm: Pointer to Alarm structure * @param Format: Specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @note The Alarm register can only be written when the corresponding Alarm * is disabled (Use the HAL_RTC_DeactivateAlarm()). * @note The HAL_RTC_SetTime() must be called before enabling the Alarm feature. * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format) { uint32_t tickstart = 0; uint32_t tmpreg = 0, subsecondtmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); assert_param(IS_RTC_ALARM(sAlarm->Alarm)); assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask)); assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel)); assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds)); assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; if(Format == RTC_FORMAT_BIN) { if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) { assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours)); assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); } else { sAlarm->AlarmTime.TimeFormat = 0x00; assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours)); } assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes)); assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds)); if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) { assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay)); } else { assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay)); } tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << 16) | \ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << 8) | \ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << 24) | \ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ ((uint32_t)sAlarm->AlarmMask)); } else { if((hrtc->Instance->CR & RTC_CR_FMT) != (uint32_t)RESET) { tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); assert_param(IS_RTC_HOUR12(tmpreg)); assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat)); } else { sAlarm->AlarmTime.TimeFormat = 0x00; assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours))); } assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes))); assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds))); if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE) { tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(tmpreg)); } else { tmpreg = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(tmpreg)); } tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << 16) | \ ((uint32_t)(sAlarm->AlarmTime.Minutes) << 8) | \ ((uint32_t) sAlarm->AlarmTime.Seconds) | \ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << 16) | \ ((uint32_t)(sAlarm->AlarmDateWeekDay) << 24) | \ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \ ((uint32_t)sAlarm->AlarmMask)); } /* Configure the Alarm A or Alarm B Sub Second registers */ subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask)); /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the Alarm register */ if(sAlarm->Alarm == RTC_ALARM_A) { /* Disable the Alarm A interrupt */ __HAL_RTC_ALARMA_DISABLE(hrtc); /* Clear flag alarm A */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF); tickstart = HAL_GetTick(); /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } hrtc->Instance->ALRMAR = (uint32_t)tmpreg; /* Configure the Alarm A Sub Second register */ hrtc->Instance->ALRMASSR = subsecondtmpreg; /* Configure the Alarm state: Enable Alarm */ __HAL_RTC_ALARMA_ENABLE(hrtc); /* Configure the Alarm interrupt */ __HAL_RTC_ALARM_ENABLE_IT(hrtc,RTC_IT_ALRA); } else { /* Disable the Alarm B interrupt */ __HAL_RTC_ALARMB_DISABLE(hrtc); /* Clear flag alarm B */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF); tickstart = HAL_GetTick(); /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } hrtc->Instance->ALRMBR = (uint32_t)tmpreg; /* Configure the Alarm B Sub Second register */ hrtc->Instance->ALRMBSSR = subsecondtmpreg; /* Configure the Alarm state: Enable Alarm */ __HAL_RTC_ALARMB_ENABLE(hrtc); /* Configure the Alarm interrupt */ __HAL_RTC_ALARM_ENABLE_IT(hrtc, RTC_IT_ALRB); } /* RTC Alarm Interrupt Configuration: EXTI configuration */ __HAL_RTC_ALARM_EXTI_ENABLE_IT(); __HAL_RTC_ALARM_EXTI_ENABLE_RISING_EDGE(); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactive the specified RTC Alarm * @param hrtc: RTC handle * @param Alarm: Specifies the Alarm. * This parameter can be one of the following values: * @arg RTC_ALARM_A: AlarmA * @arg RTC_ALARM_B: AlarmB * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm) { uint32_t tickstart = 0; /* Check the parameters */ assert_param(IS_RTC_ALARM(Alarm)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); if(Alarm == RTC_ALARM_A) { /* AlarmA */ __HAL_RTC_ALARMA_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA); tickstart = HAL_GetTick(); /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == RESET) { if( (HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } } else { /* AlarmB */ __HAL_RTC_ALARMB_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_ALARM_DISABLE_IT(hrtc,RTC_IT_ALRB); tickstart = HAL_GetTick(); /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Gets the RTC Alarm value and masks. * @param hrtc: RTC handle * @param sAlarm: Pointer to Date structure * @param Alarm: Specifies the Alarm. * This parameter can be one of the following values: * @arg RTC_ALARM_A: AlarmA * @arg RTC_ALARM_B: AlarmB * @param Format: Specifies the format of the entered parameters. * This parameter can be one of the following values: * @arg RTC_FORMAT_BIN: Binary data format * @arg RTC_FORMAT_BCD : BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format) { uint32_t tmpreg = 0, subsecondtmpreg = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); assert_param(IS_RTC_ALARM(Alarm)); if(Alarm == RTC_ALARM_A) { /* AlarmA */ sAlarm->Alarm = RTC_ALARM_A; tmpreg = (uint32_t)(hrtc->Instance->ALRMAR); subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMASSR ) & RTC_ALRMASSR_SS); /* Fill the structure with the read parameters */ sAlarm->AlarmTime.Hours = (uint32_t)((tmpreg & (RTC_ALRMAR_HT | RTC_ALRMAR_HU)) >> 16); sAlarm->AlarmTime.Minutes = (uint32_t)((tmpreg & (RTC_ALRMAR_MNT | RTC_ALRMAR_MNU)) >> 8); sAlarm->AlarmTime.Seconds = (uint32_t)(tmpreg & (RTC_ALRMAR_ST | RTC_ALRMAR_SU)); sAlarm->AlarmTime.TimeFormat = (uint32_t)((tmpreg & RTC_ALRMAR_PM) >> 16); sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg; sAlarm->AlarmDateWeekDay = (uint32_t)((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> 24); sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMAR_WDSEL); sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL); } else { sAlarm->Alarm = RTC_ALARM_B; tmpreg = (uint32_t)(hrtc->Instance->ALRMBR); subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMBSSR) & RTC_ALRMBSSR_SS); /* Fill the structure with the read parameters */ sAlarm->AlarmTime.Hours = (uint32_t)((tmpreg & (RTC_ALRMBR_HT | RTC_ALRMBR_HU)) >> 16); sAlarm->AlarmTime.Minutes = (uint32_t)((tmpreg & (RTC_ALRMBR_MNT | RTC_ALRMBR_MNU)) >> 8); sAlarm->AlarmTime.Seconds = (uint32_t)(tmpreg & (RTC_ALRMBR_ST | RTC_ALRMBR_SU)); sAlarm->AlarmTime.TimeFormat = (uint32_t)((tmpreg & RTC_ALRMBR_PM) >> 16); sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg; sAlarm->AlarmDateWeekDay = (uint32_t)((tmpreg & (RTC_ALRMBR_DT | RTC_ALRMBR_DU)) >> 24); sAlarm->AlarmDateWeekDaySel = (uint32_t)(tmpreg & RTC_ALRMBR_WDSEL); sAlarm->AlarmMask = (uint32_t)(tmpreg & RTC_ALARMMASK_ALL); } if(Format == RTC_FORMAT_BIN) { sAlarm->AlarmTime.Hours = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours); sAlarm->AlarmTime.Minutes = RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes); sAlarm->AlarmTime.Seconds = RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds); sAlarm->AlarmDateWeekDay = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay); } return HAL_OK; } /** * @brief This function handles Alarm interrupt request. * @param hrtc: RTC handle * @retval None */ void HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef* hrtc) { if(__HAL_RTC_ALARM_GET_IT(hrtc, RTC_IT_ALRA)) { /* Get the status of the Interrupt */ if((uint32_t)(hrtc->Instance->CR & RTC_IT_ALRA) != (uint32_t)RESET) { /* AlarmA callback */ HAL_RTC_AlarmAEventCallback(hrtc); /* Clear the Alarm interrupt pending bit */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRAF); } } if(__HAL_RTC_ALARM_GET_IT(hrtc, RTC_IT_ALRB)) { /* Get the status of the Interrupt */ if((uint32_t)(hrtc->Instance->CR & RTC_IT_ALRB) != (uint32_t)RESET) { /* AlarmB callback */ HAL_RTCEx_AlarmBEventCallback(hrtc); /* Clear the Alarm interrupt pending bit */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc,RTC_FLAG_ALRBF); } } /* Clear the EXTI's line Flag for RTC Alarm */ __HAL_RTC_ALARM_EXTI_CLEAR_FLAG(); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; } /** * @brief Alarm A callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTC_AlarmAEventCallback could be implemented in the user file */ } /** * @brief This function handles AlarmA Polling request. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) == RESET) { if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the Alarm interrupt pending bit */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @} */ /** @addtogroup RTC_Exported_Functions_Group4 * @brief Peripheral Control functions * @verbatim =============================================================================== ##### Peripheral Control functions ##### =============================================================================== [..] This subsection provides functions allowing to (+) Wait for RTC Time and Date Synchronization @endverbatim * @{ */ /** * @brief Waits until the RTC Time and Date registers (RTC_TR and RTC_DR) are * synchronized with RTC APB clock. * @note The RTC Resynchronization mode is write protected, use the * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function. * @note To read the calendar through the shadow registers after Calendar * initialization, calendar update or after wakeup from low power modes * the software must first clear the RSF flag. * The software must then wait until it is set again before reading * the calendar, which means that the calendar registers have been * correctly copied into the RTC_TR and RTC_DR shadow registers. * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTC_WaitForSynchro(RTC_HandleTypeDef* hrtc) { uint32_t tickstart = 0; /* Clear RSF flag */ hrtc->Instance->ISR &= (uint32_t)RTC_RSF_MASK; tickstart = HAL_GetTick(); /* Wait the registers to be synchronised */ while((hrtc->Instance->ISR & RTC_ISR_RSF) == (uint32_t)RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } return HAL_OK; } /** * @} */ /** @addtogroup RTC_Exported_Functions_Group5 * @brief Peripheral State functions * @verbatim =============================================================================== ##### Peripheral State functions ##### =============================================================================== [..] This subsection provides functions allowing to (+) Get RTC state @endverbatim * @{ */ /** * @brief Returns the RTC state. * @param hrtc: RTC handle * @retval HAL state */ HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef* hrtc) { return hrtc->State; } /** * @} */ /** * @} */ /** @addtogroup RTC_Private_Functions * @{ */ /** * @brief Enters the RTC Initialization mode. * @note The RTC Initialization mode is write protected, use the * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function. * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef RTC_EnterInitMode(RTC_HandleTypeDef* hrtc) { uint32_t tickstart = 0; /* Check if the Initialization mode is set */ if((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET) { /* Set the Initialization mode */ hrtc->Instance->ISR = (uint32_t)RTC_INIT_MASK; tickstart = HAL_GetTick(); /* Wait till RTC is in INIT state and if Time out is reached exit */ while((hrtc->Instance->ISR & RTC_ISR_INITF) == (uint32_t)RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { return HAL_TIMEOUT; } } } return HAL_OK; } /** * @brief Converts a 2 digit decimal to BCD format. * @param Value: Byte to be converted * @retval Converted byte */ uint8_t RTC_ByteToBcd2(uint8_t Value) { uint32_t bcdhigh = 0; while(Value >= 10) { bcdhigh++; Value -= 10; } return ((uint8_t)(bcdhigh << 4) | Value); } /** * @brief Converts from 2 digit BCD to Binary. * @param Value: BCD value to be converted * @retval Converted word */ uint8_t RTC_Bcd2ToByte(uint8_t Value) { uint32_t tmp = 0; tmp = ((uint8_t)(Value & (uint8_t)0xF0) >> (uint8_t)0x4) * 10; return (tmp + (Value & (uint8_t)0x0F)); } /** * @} */ #endif /* HAL_RTC_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/