#---------------------------------------------------------------------------- # On command line: # # make all = Make software. # # make clean = Clean out built project files. # # make coff = Convert ELF to AVR COFF. # # make extcoff = Convert ELF to AVR Extended COFF. # # make program = Download the hex file to the device. # Please customize your programmer settings(PROGRAM_CMD) # # make teensy = Download the hex file to the device, using teensy_loader_cli. # (must have teensy_loader_cli installed). # # make dfu = Download the hex file to the device, using dfu-programmer (must # have dfu-programmer installed). # # make flip = Download the hex file to the device, using Atmel FLIP (must # have Atmel FLIP installed). # # make dfu-ee = Download the eeprom file to the device, using dfu-programmer # (must have dfu-programmer installed). # # make flip-ee = Download the eeprom file to the device, using Atmel FLIP # (must have Atmel FLIP installed). # # make debug = Start either simulavr or avarice as specified for debugging, # with avr-gdb or avr-insight as the front end for debugging. # # make filename.s = Just compile filename.c into the assembler code only. # # make filename.i = Create a preprocessed source file for use in submitting # bug reports to the GCC project. # # To rebuild project do "make clean" then "make all". #---------------------------------------------------------------------------- # Target file name (without extension). TARGET ?= usb_usb TMK_DIR ?= ../../tmk_core # Directory keyboard dependent files exist TARGET_DIR ?= . # MCU name MCU ?= atmega32u4 # Processor frequency. # This will define a symbol, F_CPU, in all source code files equal to the # processor frequency in Hz. You can then use this symbol in your source code to # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # # This will be an integer division of F_USB below, as it is sourced by # F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. F_CPU ?= 16000000 # # LUFA specific # # Target architecture (see library "Board Types" documentation). ARCH ?= AVR8 # Input clock frequency. # This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' # at the end, this will be done automatically to create a 32-bit value in your # source code. # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB ?= $(F_CPU) # Interrupt driven control endpoint task OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Build Options # comment out to disable the options. # MOUSEKEY_ENABLE ?= yes # Mouse keys EXTRAKEY_ENABLE ?= yes # Media control and System control CONSOLE_ENABLE ?= yes # Console for debug #COMMAND_ENABLE ?= yes # Commands for debug and configuration #NKRO_ENABLE ?= yes # USB Nkey Rollover # Boot Section Size in bytes # Teensy halfKay 512 # Atmel DFU loader 4096 # LUFA bootloader 4096 OPT_DEFS += -DBOOTLOADER_SIZE=4096 #LDFLAGS += -Wl,--relax #OPT_DEFS += -DNO_ACTION_TAPPING #OPT_DEFS += -DNO_ACTION_LAYER #OPT_DEFS += -DNO_ACTION_MACRO SRC ?= usb_usb.cpp \ main.cpp # # Keymap file # ifeq (yes,$(strip $(UNIMAP_ENABLE))) KEYMAP_FILE = unimap else ifeq (yes,$(strip $(ACTIONMAP_ENABLE))) KEYMAP_FILE = actionmap else KEYMAP_FILE = keymap endif endif ifdef KEYMAP SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) else SRC := $(KEYMAP_FILE).c $(SRC) endif CONFIG_H ?= config.h # Search Path VPATH += $(TARGET_DIR) VPATH += $(TMK_DIR) # program Leonardo PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -b57600 -Uflash:w:$(TARGET).hex -P$(DEV) include $(TMK_DIR)/protocol/usb_hid.mk include $(TMK_DIR)/protocol/lufa.mk include $(TMK_DIR)/common.mk include $(TMK_DIR)/rules.mk