/** ****************************************************************************** * @file stm32l0xx_hal_rtc_ex.c * @author MCD Application Team * @version V1.2.0 * @date 06-February-2015 * @brief Extended RTC HAL module driver. * * This file provides firmware functions to manage the following * functionalities of the Real Time Clock (RTC) Extended peripheral: * + RTC Time Stamp functions * + RTC Tamper functions * + RTC Wake-up functions * + Extended Control functions * + Extended RTC features functions * @verbatim ============================================================================== ##### Backup Domain Operating Condition ##### ============================================================================== [..] As long as the supply voltage remains in the operating range, the RTC never stops, regardless of the device status (Run mode, low power modes or under reset). ##### Backup Domain Reset ##### ================================================================== [..] The backup domain reset sets all RTC registers and the RCC_CSR register to their reset values. [..] A backup domain reset is generated when one of the following events occurs: (+) Software reset, triggered by setting the RTCRST bit in the RCC Control Status register (RCC_CSR). (+) Power reset (BOR/POR/PDR). ##### Backup Domain Access ##### ================================================================== [..] After reset, the backup domain (RTC registers and RTC backup data registers) is protected against possible unwanted write accesses. [..] To enable access to the RTC Domain and RTC registers, proceed as follows: (+) Enable the Power Controller (PWR) APB1 interface clock using the __HAL_RCC_PWR_CLK_ENABLE() function. (+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. (+) Select the RTC clock source using the __HAL_RCC_RTC_CONFIG() function. (+) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() function. ##### How to use this driver ##### ============================================================================== [..] (+) Enable the RTC domain access. (+) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour format using the HAL_RTC_Init() function. *** Time and Date configuration *** =================================== [..] (+) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime() and HAL_RTC_SetDate() functions. (+) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions. *** Alarm configuration *** =========================== [..] (+) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function. You can also configure the RTC Alarm with interrupt mode using the HAL_RTC_SetAlarm_IT() function. (+) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function. *** RTC Wakeup configuration *** ================================ [..] (+) To configure the RTC Wakeup Clock source and Counter use the HAL_RTCEx_SetWakeUpTimer() function. You can also configure the RTC Wakeup timer with interrupt mode using the HAL_RTCEx_SetWakeUpTimer_IT() function. (+) To read the RTC WakeUp Counter register, use the HAL_RTCEx_GetWakeUpTimer() function. *** Outputs configuration *** ============================= [..] The RTC has 2 different outputs: (+) RTC_ALARM: this output is used to manage the RTC Alarm A, Alarm B and WaKeUp signals. To output the selected RTC signal, use the HAL_RTC_Init() function. (+) RTC_CALIB: this output is 512Hz signal or 1Hz. To enable the RTC_CALIB, use the HAL_RTCEx_SetCalibrationOutPut() function. (+) Two pins can be used as RTC_ALARM or RTC_CALIB (PC13, PB14) managed on the RTC_OR register. (+) When the RTC_CALIB or RTC_ALARM output is selected, the RTC_OUT pin is automatically configured in output alternate function. *** Smooth digital Calibration configuration *** ================================================ [..] (+) Configure the RTC Original Digital Calibration Value and the corresponding calibration cycle period (32s,16s and 8s) using the HAL_RTCEx_SetSmoothCalib() function. *** TimeStamp configuration *** =============================== [..] (+) Enables the RTC TimeStamp using the HAL_RTC_SetTimeStamp() function. You can also configure the RTC TimeStamp with interrupt mode using the HAL_RTC_SetTimeStamp_IT() function. (+) To read the RTC TimeStamp Time and Date register, use the HAL_RTC_GetTimeStamp() function. *** Tamper configuration *** ============================ [..] (+) Enable the RTC Tamper and Configure the Tamper filter count, trigger Edge or Level according to the Tamper filter (if equal to 0 Edge else Level) value, sampling frequency, NoErase, MaskFlag, precharge or discharge and Pull-UP using the HAL_RTC_SetTamper() function. You can configure RTC Tamper with interrupt mode using HAL_RTC_SetTamper_IT() function. (+) The default configuration of the Tamper erases the backup registers. To avoid erase, enable the NoErase field on the RTC_TAMPCR register. *** Backup Data Registers configuration *** =========================================== [..] (+) To write to the RTC Backup Data registers, use the HAL_RTC_BKUPWrite() function. (+) To read the RTC Backup Data registers, use the HAL_RTC_BKUPRead() function. (+) The backup registers are reset when a tamper detection event occurs ##### RTC and low power modes ##### ================================================================== [..] The MCU can be woken up from a low power mode by an RTC alternate function. [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B), RTC wakeup, RTC tamper event detection and RTC time stamp event detection. These RTC alternate functions can wake up the system from the Stop and Standby low power modes. [..] The system can also wake up from low power modes without depending on an external interrupt (Auto-wakeup mode), by using the RTC alarm or the RTC wakeup events. [..] The RTC provides a programmable time base for waking up from the Stop or Standby mode at regular intervals. Wakeup from STOP and Standby modes is possible only when the RTC clock source is LSE or LSI. @endverbatim ****************************************************************************** * @attention * *

© COPYRIGHT(c) 2015 STMicroelectronics

* * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32l0xx_hal.h" /** @addtogroup STM32L0xx_HAL_Driver * @{ */ /** @addtogroup RTCEx * @brief RTC Extended HAL module driver * @{ */ #ifdef HAL_RTC_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ /* Exported functions --------------------------------------------------------*/ /** @addtogroup RTCEx_Exported_Functions * @{ */ /** @addtogroup RTCEx_Exported_Functions_Group1 * @brief RTC TimeStamp and Tamper functions * @verbatim =============================================================================== ##### RTC TimeStamp and Tamper functions ##### =============================================================================== [..] This section provide functions allowing to configure TimeStamp feature @endverbatim * @{ */ /** * @brief Sets TimeStamp. * @note This API must be called before enabling the TimeStamp feature. * @param hrtc: RTC handle * @param TimeStampEdge: Specifies the pin edge on which the TimeStamp is * activated. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the * rising edge of the related pin. * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the * falling edge of the related pin. * @param RTC_TimeStampPin: specifies the RTC TimeStamp Pin. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPPIN_PC13: PC13 is selected as RTC TimeStamp Pin. * The RTC TimeStamp Pin is per default PC13, but for reasons of * compatibility, this parameter is used. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge)); assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Get the RTC_CR register and clear the bits to be configured */ tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); tmpreg|= TimeStampEdge; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the Time Stamp TSEDGE and Enable bits */ hrtc->Instance->CR = (uint32_t)tmpreg; __HAL_RTC_TIMESTAMP_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Sets TimeStamp with Interrupt. * @param hrtc: RTC handle * @note This API must be called before enabling the TimeStamp feature. * @param TimeStampEdge: Specifies the pin edge on which the TimeStamp is * activated. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPEDGE_RISING: the Time stamp event occurs on the * rising edge of the related pin. * @arg RTC_TIMESTAMPEDGE_FALLING: the Time stamp event occurs on the * falling edge of the related pin. * @param RTC_TimeStampPin: Specifies the RTC TimeStamp Pin. * This parameter can be one of the following values: * @arg RTC_TIMESTAMPPIN_PC13: PC13 is selected as RTC TimeStamp Pin. * The RTC TimeStamp Pin is per default PC13, but for reasons of * compatibility, this parameter is used. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTimeStamp_IT(RTC_HandleTypeDef *hrtc, uint32_t TimeStampEdge, uint32_t RTC_TimeStampPin) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param(IS_TIMESTAMP_EDGE(TimeStampEdge)); assert_param(IS_RTC_TIMESTAMP_PIN(RTC_TimeStampPin)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Get the RTC_CR register and clear the bits to be configured */ tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); tmpreg |= TimeStampEdge; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Configure the Time Stamp TSEDGE and Enable bits */ hrtc->Instance->CR = (uint32_t)tmpreg; __HAL_RTC_TIMESTAMP_ENABLE(hrtc); /* Enable IT timestamp */ __HAL_RTC_TIMESTAMP_ENABLE_IT(hrtc,RTC_IT_TS); /* RTC timestamp Interrupt Configuration: EXTI configuration */ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE(); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivates TimeStamp. * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateTimeStamp(RTC_HandleTypeDef *hrtc) { uint32_t tmpreg = 0; /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_TIMESTAMP_DISABLE_IT(hrtc, RTC_IT_TS); /* Get the RTC_CR register and clear the bits to be configured */ tmpreg = (uint32_t)(hrtc->Instance->CR & (uint32_t)~(RTC_CR_TSEDGE | RTC_CR_TSE)); /* Configure the Time Stamp TSEDGE and Enable bits */ hrtc->Instance->CR = (uint32_t)tmpreg; /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Gets the RTC TimeStamp value. * @param hrtc: RTC handle * @param sTimeStamp: Pointer to Time structure * @param sTimeStampDate: Pointer to Date structure * @param Format: specifies the format of the entered parameters. * This parameter can be one of the following values: * RTC_FORMAT_BIN: Binary data format * RTC_FORMAT_BCD : BCD data format * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_GetTimeStamp(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef* sTimeStamp, RTC_DateTypeDef* sTimeStampDate, uint32_t Format) { uint32_t tmptime = 0, tmpdate = 0; /* Check the parameters */ assert_param(IS_RTC_FORMAT(Format)); /* Get the TimeStamp time and date registers values */ tmptime = (uint32_t)(hrtc->Instance->TSTR & RTC_TR_RESERVED_MASK); tmpdate = (uint32_t)(hrtc->Instance->TSDR & RTC_DR_RESERVED_MASK); /* Fill the Time structure fields with the read parameters */ sTimeStamp->Hours = (uint8_t)((tmptime & (RTC_TR_HT | RTC_TR_HU)) >> 16); sTimeStamp->Minutes = (uint8_t)((tmptime & (RTC_TR_MNT | RTC_TR_MNU)) >> 8); sTimeStamp->Seconds = (uint8_t)(tmptime & (RTC_TR_ST | RTC_TR_SU)); sTimeStamp->TimeFormat = (uint8_t)((tmptime & (RTC_TR_PM)) >> 16); sTimeStamp->SubSeconds = (uint32_t) hrtc->Instance->TSSSR; /* Fill the Date structure fields with the read parameters */ sTimeStampDate->Year = 0; sTimeStampDate->Month = (uint8_t)((tmpdate & (RTC_DR_MT | RTC_DR_MU)) >> 8); sTimeStampDate->Date = (uint8_t)(tmpdate & (RTC_DR_DT | RTC_DR_DU)); sTimeStampDate->WeekDay = (uint8_t)((tmpdate & (RTC_DR_WDU)) >> 13); /* Check the input parameters format */ if(Format == RTC_FORMAT_BIN) { /* Convert the TimeStamp structure parameters to Binary format */ sTimeStamp->Hours = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Hours); sTimeStamp->Minutes = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Minutes); sTimeStamp->Seconds = (uint8_t)RTC_Bcd2ToByte(sTimeStamp->Seconds); /* Convert the DateTimeStamp structure parameters to Binary format */ sTimeStampDate->Month = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Month); sTimeStampDate->Date = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->Date); sTimeStampDate->WeekDay = (uint8_t)RTC_Bcd2ToByte(sTimeStampDate->WeekDay); } /* Clear the TIMESTAMP Flag */ __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSF); return HAL_OK; } /** * @brief Sets Tamper * @note By calling this API we disable the tamper interrupt for all tampers. * @param hrtc: RTC handle * @param sTamper: Pointer to Tamper Structure. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef* sTamper) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param( IS_RTC_TAMPER(sTamper->Tamper)); assert_param( IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Configure the tamper trigger */ if(sTamper->Trigger != RTC_TAMPERTRIGGER_RISINGEDGE) { sTamper->Trigger = (uint32_t)(sTamper->Tamper << 1); } if(sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) { sTamper->NoErase = 0; if((sTamper->Tamper & RTC_TAMPER_1) != 0) { sTamper->NoErase |= RTC_TAMPCR_TAMP1NOERASE; } if((sTamper->Tamper & RTC_TAMPER_2) != 0) { sTamper->NoErase |= RTC_TAMPCR_TAMP2NOERASE; } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) if((sTamper->Tamper & RTC_TAMPER_3) != 0) { sTamper->NoErase |= RTC_TAMPCR_TAMP3NOERASE; } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ } if(sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) { sTamper->MaskFlag = 0; if((sTamper->Tamper & RTC_TAMPER_1) != 0) { sTamper->MaskFlag |= RTC_TAMPCR_TAMP1MF; } if((sTamper->Tamper & RTC_TAMPER_2) != 0) { sTamper->MaskFlag |= RTC_TAMPCR_TAMP2MF; } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) if((sTamper->Tamper & RTC_TAMPER_3) != 0) { sTamper->MaskFlag |= RTC_TAMPCR_TAMP3MF; } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ } /* Configure the RTC_TAMPCR register */ tmpreg = (uint32_t)((uint32_t)sTamper->Tamper | (uint32_t)sTamper->Trigger | (uint32_t)sTamper->NoErase |\ (uint32_t)sTamper->MaskFlag | (uint32_t)sTamper->Filter | (uint32_t)sTamper->SamplingFrequency |\ (uint32_t)sTamper->PrechargeDuration | (uint32_t)sTamper->TamperPullUp | (uint32_t)sTamper->TimeStampOnTamperDetection); #if defined (STM32L063xx) || defined (STM32L062xx) || defined (STM32L061xx) || \ defined (STM32L053xx) || defined (STM32L052xx) || defined (STM32L051xx) hrtc->Instance->TAMPCR &= ((uint32_t)~((uint32_t)sTamper->Tamper | (uint32_t)(sTamper->Tamper << 1) | RTC_TAMPCR_TAMPTS |\ RTC_TAMPCR_TAMPFREQ | RTC_TAMPCR_TAMPFLT | RTC_TAMPCR_TAMPPRCH |\ RTC_TAMPCR_TAMPPUDIS | RTC_TAMPCR_TAMPIE | RTC_TAMPCR_TAMP1IE |\ RTC_TAMPCR_TAMP2IE | RTC_TAMPCR_TAMP1NOERASE | RTC_TAMPCR_TAMP2NOERASE|\ RTC_TAMPCR_TAMP1MF | RTC_TAMPCR_TAMP2MF)); #endif /* (STM32L063xx) || (STM32L062xx) || (STM32L061xx) || * (STM32L053xx) || (STM32L052xx) || (STM32L051xx) */ #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) hrtc->Instance->TAMPCR &= ((uint32_t)~((uint32_t)sTamper->Tamper | (uint32_t)(sTamper->Tamper << 1) | RTC_TAMPCR_TAMPTS |\ RTC_TAMPCR_TAMPFREQ | RTC_TAMPCR_TAMPFLT | RTC_TAMPCR_TAMPPRCH |\ RTC_TAMPCR_TAMPPUDIS | RTC_TAMPCR_TAMPIE | RTC_TAMPCR_TAMP1IE |\ RTC_TAMPCR_TAMP2IE | RTC_TAMPCR_TAMP3IE | RTC_TAMPCR_TAMP1NOERASE |\ RTC_TAMPCR_TAMP2NOERASE | RTC_TAMPCR_TAMP3NOERASE | RTC_TAMPCR_TAMP1MF |\ RTC_TAMPCR_TAMP2MF | RTC_TAMPCR_TAMP3MF)); #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ hrtc->Instance->TAMPCR |= tmpreg; hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Sets Tamper with interrupt. * @note By calling this API we force the tamper interrupt for all tampers. * @param hrtc: RTC handle * @param sTamper: Pointer to RTC Tamper. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef* sTamper) { uint32_t tmpreg = 0; /* Check the parameters */ assert_param( IS_RTC_TAMPER(sTamper->Tamper)); assert_param(IS_RTC_TAMPER_INTERRUPT(sTamper->Interrupt)); assert_param( IS_RTC_TAMPER_TRIGGER(sTamper->Trigger)); assert_param(IS_RTC_TAMPER_ERASE_MODE(sTamper->NoErase)); assert_param(IS_RTC_TAMPER_MASKFLAG_STATE(sTamper->MaskFlag)); assert_param(IS_RTC_TAMPER_FILTER(sTamper->Filter)); assert_param(IS_RTC_TAMPER_SAMPLING_FREQ(sTamper->SamplingFrequency)); assert_param(IS_RTC_TAMPER_PRECHARGE_DURATION(sTamper->PrechargeDuration)); assert_param(IS_RTC_TAMPER_PULLUP_STATE(sTamper->TamperPullUp)); assert_param(IS_RTC_TAMPER_TIMESTAMPONTAMPER_DETECTION(sTamper->TimeStampOnTamperDetection)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Configure the tamper trigger */ if(sTamper->Trigger != RTC_TAMPERTRIGGER_RISINGEDGE) { sTamper->Trigger = (uint32_t)(sTamper->Tamper << 1); } if(sTamper->NoErase != RTC_TAMPER_ERASE_BACKUP_ENABLE) { sTamper->NoErase = 0; if((sTamper->Tamper & RTC_TAMPER_1) != 0) { sTamper->NoErase |= RTC_TAMPCR_TAMP1NOERASE; } if((sTamper->Tamper & RTC_TAMPER_2) != 0) { sTamper->NoErase |= RTC_TAMPCR_TAMP2NOERASE; } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) if((sTamper->Tamper & RTC_TAMPER_3) != 0) { sTamper->NoErase |= RTC_TAMPCR_TAMP3NOERASE; } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ } if(sTamper->MaskFlag != RTC_TAMPERMASK_FLAG_DISABLE) { sTamper->MaskFlag = 0; if((sTamper->Tamper & RTC_TAMPER_1) != 0) { sTamper->MaskFlag |= RTC_TAMPCR_TAMP1MF; } if((sTamper->Tamper & RTC_TAMPER_2) != 0) { sTamper->MaskFlag |= RTC_TAMPCR_TAMP2MF; } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) if((sTamper->Tamper & RTC_TAMPER_3) != 0) { sTamper->MaskFlag |= RTC_TAMPCR_TAMP3MF; } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ } /* Configure the RTC_TAMPCR register */ tmpreg = (uint32_t)((uint32_t)sTamper->Tamper | (uint32_t)sTamper->Interrupt | (uint32_t)sTamper->Trigger | (uint32_t)sTamper->NoErase |\ (uint32_t)sTamper->MaskFlag | (uint32_t)sTamper->Filter | (uint32_t)sTamper->SamplingFrequency |\ (uint32_t)sTamper->PrechargeDuration | (uint32_t)sTamper->TamperPullUp | (uint32_t)sTamper->TimeStampOnTamperDetection); #if defined (STM32L063xx) || defined (STM32L062xx) || defined (STM32L061xx) || \ defined (STM32L053xx) || defined (STM32L052xx) || defined (STM32L051xx) hrtc->Instance->TAMPCR &= (uint32_t)~((uint32_t)sTamper->Tamper | (uint32_t)(sTamper->Tamper << 1) | RTC_TAMPCR_TAMPTS |\ RTC_TAMPCR_TAMPFREQ | RTC_TAMPCR_TAMPFLT | RTC_TAMPCR_TAMPPRCH |\ RTC_TAMPCR_TAMPPUDIS | RTC_TAMPCR_TAMPIE | RTC_TAMPCR_TAMP1IE |\ RTC_TAMPCR_TAMP2IE | RTC_TAMPCR_TAMP1NOERASE | RTC_TAMPCR_TAMP2NOERASE |\ RTC_TAMPCR_TAMP1MF | RTC_TAMPCR_TAMP2MF); #endif /* (STM32L063xx) || (STM32L062xx) || (STM32L061xx) || * (STM32L053xx) || (STM32L052xx) || (STM32L051xx) */ #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) hrtc->Instance->TAMPCR &= (uint32_t)~((uint32_t)sTamper->Tamper | (uint32_t)(sTamper->Tamper << 1) | RTC_TAMPCR_TAMPTS |\ RTC_TAMPCR_TAMPFREQ | RTC_TAMPCR_TAMPFLT | RTC_TAMPCR_TAMPPRCH |\ RTC_TAMPCR_TAMPPUDIS | RTC_TAMPCR_TAMPIE | RTC_TAMPCR_TAMP1IE |\ RTC_TAMPCR_TAMP2IE | RTC_TAMPCR_TAMP3IE | RTC_TAMPCR_TAMP1NOERASE |\ RTC_TAMPCR_TAMP2NOERASE | RTC_TAMPCR_TAMP3NOERASE | RTC_TAMPCR_TAMP1MF |\ RTC_TAMPCR_TAMP2MF | RTC_TAMPCR_TAMP3MF); #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ hrtc->Instance->TAMPCR |= tmpreg; /* RTC Tamper Interrupt Configuration: EXTI configuration */ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT(); __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_RISING_EDGE(); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivates Tamper. * @param hrtc: RTC handle * @param Tamper: Selected tamper pin. * This parameter can be RTC_Tamper_1 and/or RTC_TAMPER_2 for NEMO. * This parameter can be any combination of RTC_TAMPER_1, RTC_TAMPER_2 and RTC_TAMPER_3 for BIG NEMO. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef *hrtc, uint32_t Tamper) { assert_param( IS_RTC_TAMPER(Tamper)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the selected Tamper pin */ hrtc->Instance->TAMPCR &= ((uint32_t)~Tamper); if ((Tamper & RTC_TAMPER_1) != 0) { /* Disable the Tamper1 interrupt */ hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP1)); } if ((Tamper & RTC_TAMPER_2) != 0) { /* Disable the Tamper2 interrupt */ hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP2)); } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) if ((Tamper & RTC_TAMPER_3) != 0) { /* Disable the Tamper2 interrupt */ hrtc->Instance->TAMPCR &= ((uint32_t)~(RTC_IT_TAMP | RTC_IT_TAMP3)); } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief This function handles TimeStamp interrupt request. * @param hrtc: RTC handle * @retval None */ void HAL_RTCEx_TamperTimeStampIRQHandler(RTC_HandleTypeDef *hrtc) { if(__HAL_RTC_TIMESTAMP_GET_IT(hrtc, RTC_IT_TS)) { /* Get the status of the Interrupt */ if((uint32_t)(hrtc->Instance->CR & RTC_IT_TS) != (uint32_t)RESET) { /* TIMESTAMP callback */ HAL_RTCEx_TimeStampEventCallback(hrtc); /* Clear the TIMESTAMP interrupt pending bit */ __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc,RTC_FLAG_TSF); } } /* Get the status of the Interrupt */ if(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F)== SET) { /* Get the TAMPER Interrupt enable bit and pending bit */ if((((hrtc->Instance->TAMPCR & RTC_TAMPCR_TAMPIE)) != (uint32_t)RESET) || \ (((hrtc->Instance->TAMPCR & RTC_TAMPCR_TAMP1IE)) != (uint32_t)RESET)) { /* Tamper callback */ HAL_RTCEx_Tamper1EventCallback(hrtc); /* Clear the Tamper interrupt pending bit */ __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP1F); } } /* Get the status of the Interrupt */ if(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F)== SET) { /* Get the TAMPER Interrupt enable bit and pending bit */ if((((hrtc->Instance->TAMPCR & RTC_TAMPCR_TAMPIE)) != (uint32_t)RESET) || \ (((hrtc->Instance->TAMPCR & RTC_TAMPCR_TAMP2IE)) != (uint32_t)RESET)) { /* Tamper callback */ HAL_RTCEx_Tamper2EventCallback(hrtc); /* Clear the Tamper interrupt pending bit */ __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP2F); } } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) /* Get the status of the Interrupt */ if(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP3F)== SET) { /* Get the TAMPER Interrupt enable bit and pending bit */ if((((hrtc->Instance->TAMPCR & RTC_TAMPCR_TAMPIE)) != (uint32_t)RESET) || \ (((hrtc->Instance->TAMPCR & RTC_TAMPCR_TAMP3IE)) != (uint32_t)RESET)) { /* Tamper callback */ HAL_RTCEx_Tamper3EventCallback(hrtc); /* Clear the Tamper interrupt pending bit */ __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc, RTC_FLAG_TAMP3F); } } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ /* Clear the EXTI's Flag for RTC TimeStamp and Tamper */ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG(); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; } /** * @brief TimeStamp callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTCEx_TimeStampEventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTCEx_TimeStampEventCallback could be implemented in the user file */ } /** * @brief Tamper 1 callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTCEx_Tamper1EventCallback could be implemented in the user file */ } /** * @brief Tamper 2 callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTCEx_Tamper2EventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTCEx_Tamper2EventCallback could be implemented in the user file */ } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) /** * @brief Tamper 3 callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTCEx_Tamper3EventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTCEx_Tamper3EventCallback could be implemented in the user file */ } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ /** * @brief This function handles TimeStamp polling request. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForTimeStampEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSF) == RESET) { if(__HAL_RTC_TIMESTAMP_GET_FLAG(hrtc, RTC_FLAG_TSOVF) != RESET) { /* Clear the TIMESTAMP OverRun Flag */ __HAL_RTC_TIMESTAMP_CLEAR_FLAG(hrtc, RTC_FLAG_TSOVF); /* Change TIMESTAMP state */ hrtc->State = HAL_RTC_STATE_ERROR; return HAL_ERROR; } if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @brief This function handles Tamper1 Polling. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForTamper1Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); /* Get the status of the Interrupt */ while(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP1F)== RESET) { if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the Tamper Flag */ __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP1F); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @brief This function handles Tamper2 Polling. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForTamper2Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); /* Get the status of the Interrupt */ while(__HAL_RTC_TAMPER_GET_FLAG(hrtc, RTC_FLAG_TAMP2F) == RESET) { if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the Tamper Flag */ __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP2F); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } #if defined (STM32L083xx) || defined (STM32L082xx) || defined (STM32L081xx) || \ defined (STM32L073xx) || defined (STM32L072xx) || defined (STM32L071xx) /** * @brief This function handles Tamper3 Polling. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForTamper3Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); /* Get the status of the Interrupt */ while(__HAL_RTC_TAMPER_GET_FLAG(hrtc,RTC_FLAG_TAMP3F) == RESET) { if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the Tamper Flag */ __HAL_RTC_TAMPER_CLEAR_FLAG(hrtc,RTC_FLAG_TAMP3F); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } #endif /* (STM32L083xx) || (STM32L082xx) || (STM32L081xx) || * (STM32L073xx) || (STM32L072xx) || (STM32L071xx) */ /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group2 * @brief RTC Wake-up functions * @verbatim =============================================================================== ##### RTC Wake-up functions ##### =============================================================================== [..] This section provide functions allowing to configure Wake-up feature @endverbatim * @{ */ /** * @brief Sets wake up timer. * @param hrtc: RTC handle * @param WakeUpCounter: Wake up counter * @param WakeUpClock: Wake up clock * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock) { uint32_t tickstart = 0; /* Check the parameters */ assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock)); assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc); tickstart = HAL_GetTick(); /* Wait till RTC WUTWF flag is set and if Time out is reached exit */ while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } /* Clear the Wakeup Timer clock source bits in CR register */ hrtc->Instance->CR &= (uint32_t)~RTC_CR_WUCKSEL; /* Configure the clock source */ hrtc->Instance->CR |= (uint32_t)WakeUpClock; /* Configure the Wakeup Timer counter */ hrtc->Instance->WUTR = (uint32_t)WakeUpCounter; /* Enable the Wakeup Timer */ __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Sets wake up timer with interrupt * @param hrtc: RTC handle * @param WakeUpCounter: Wake up counter * @param WakeUpClock: Wake up clock * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetWakeUpTimer_IT(RTC_HandleTypeDef *hrtc, uint32_t WakeUpCounter, uint32_t WakeUpClock) { uint32_t tickstart = 0; /* Check the parameters */ assert_param(IS_RTC_WAKEUP_CLOCK(WakeUpClock)); assert_param(IS_RTC_WAKEUP_COUNTER(WakeUpCounter)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc); tickstart = HAL_GetTick(); /* Wait till RTC WUTWF flag is set and if Time out is reached exit */ while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } /* Configure the Wakeup Timer counter */ hrtc->Instance->WUTR = (uint32_t)WakeUpCounter; /* Clear the Wakeup Timer clock source bits in CR register */ hrtc->Instance->CR &= (uint32_t)~RTC_CR_WUCKSEL; /* Configure the clock source */ hrtc->Instance->CR |= (uint32_t)WakeUpClock; /* RTC WakeUpTimer Interrupt Configuration: EXTI configuration */ __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT(); __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_RISING_EDGE(); /* Configure the Interrupt in the RTC_CR register */ __HAL_RTC_WAKEUPTIMER_ENABLE_IT(hrtc,RTC_IT_WUT); /* Enable the Wakeup Timer */ __HAL_RTC_WAKEUPTIMER_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivates wake up timer counter. * @param hrtc: RTC handle * @retval HAL status */ uint32_t HAL_RTCEx_DeactivateWakeUpTimer(RTC_HandleTypeDef *hrtc) { uint32_t tickstart = 0; /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Disable the Wakeup Timer */ __HAL_RTC_WAKEUPTIMER_DISABLE(hrtc); /* In case of interrupt mode is used, the interrupt source must disabled */ __HAL_RTC_WAKEUPTIMER_DISABLE_IT(hrtc,RTC_IT_WUT); tickstart = HAL_GetTick(); /* Wait till RTC WUTWF flag is set and if Time out is reached exit */ while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTWF) == RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Gets wake up timer counter. * @param hrtc: RTC handle * @retval Counter value */ uint32_t HAL_RTCEx_GetWakeUpTimer(RTC_HandleTypeDef *hrtc) { /* Get the counter value */ return ((uint32_t)(hrtc->Instance->WUTR & RTC_WUTR_WUT)); } /** * @brief This function handles Wake Up Timer interrupt request. * @param hrtc: RTC handle * @retval None */ void HAL_RTCEx_WakeUpTimerIRQHandler(RTC_HandleTypeDef *hrtc) { if(__HAL_RTC_WAKEUPTIMER_GET_IT(hrtc, RTC_IT_WUT)) { /* Get the status of the Interrupt */ if((uint32_t)(hrtc->Instance->CR & RTC_IT_WUT) != (uint32_t)RESET) { /* WAKEUPTIMER callback */ HAL_RTCEx_WakeUpTimerEventCallback(hrtc); /* Clear the WAKEUPTIMER interrupt pending bit */ __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); } } /* Clear the EXTI's line Flag for RTC WakeUpTimer */ __HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG(); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; } /** * @brief Wake Up Timer callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTCEx_WakeUpTimerEventCallback could be implemented in the user file */ } /** * @brief This function handles Wake Up Timer Polling. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForWakeUpTimerEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_WAKEUPTIMER_GET_FLAG(hrtc, RTC_FLAG_WUTF) == RESET) { if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the WAKEUPTIMER Flag */ __HAL_RTC_WAKEUPTIMER_CLEAR_FLAG(hrtc, RTC_FLAG_WUTF); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group3 * @brief Extended Peripheral Control functions * @verbatim =============================================================================== ##### Extended Peripheral Control functions ##### =============================================================================== [..] This subsection provides functions allowing to (+) Writes a data in a specified RTC Backup data register (+) Read a data in a specified RTC Backup data register (+) Sets the Coarse calibration parameters. (+) Deactivates the Coarse calibration parameters (+) Sets the Smooth calibration parameters. (+) Configures the Synchronization Shift Control Settings. (+) Configures the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). (+) Deactivates the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). (+) Enables the RTC reference clock detection. (+) Disable the RTC reference clock detection. (+) Enables the Bypass Shadow feature. (+) Disables the Bypass Shadow feature. @endverbatim * @{ */ /** * @brief Writes a data in a specified RTC Backup data register. * @param hrtc: RTC handle * @param BackupRegister: RTC Backup data Register number. * This parameter can be: RTC_BKP_DRx where x can be from 0 to 19 to * specify the register. * @param Data: Data to be written in the specified RTC Backup data register. * @retval None */ void HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister, uint32_t Data) { uint32_t tmp = 0; /* Check the parameters */ assert_param(IS_RTC_BKP(BackupRegister)); tmp = (uint32_t)&(hrtc->Instance->BKP0R); tmp += (BackupRegister * 4); /* Write the specified register */ *(__IO uint32_t *)tmp = (uint32_t)Data; } /** * @brief Reads data from the specified RTC Backup data Register. * @param hrtc: RTC handle * @param BackupRegister: RTC Backup data Register number. * This parameter can be: RTC_BKP_DRx where x can be from 0 to 19 to * specify the register. * @retval Read value */ uint32_t HAL_RTCEx_BKUPRead(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister) { uint32_t tmp = 0; /* Check the parameters */ assert_param(IS_RTC_BKP(BackupRegister)); tmp = (uint32_t)&(hrtc->Instance->BKP0R); tmp += (BackupRegister * 4); /* Read the specified register */ return (*(__IO uint32_t *)tmp); } /** * @brief Sets the Smooth calibration parameters. * @param hrtc: RTC handle * @param SmoothCalibPeriod: Select the Smooth Calibration Period. * This parameter can be can be one of the following values : * @arg RTC_SMOOTHCALIB_PERIOD_32SEC: The smooth calibration periode is 32s. * @arg RTC_SMOOTHCALIB_PERIOD_16SEC: The smooth calibration periode is 16s. * @arg RTC_SMOOTHCALIB_PERIOD_8SEC: The smooth calibartion periode is 8s. * @param SmoothCalibPlusPulses: Select to Set or reset the CALP bit. * This parameter can be one of the following values: * @arg RTC_SMOOTHCALIB_PLUSPULSES_SET: Add one RTCCLK puls every 2*11 pulses. * @arg RTC_SMOOTHCALIB_PLUSPULSES_RESET: No RTCCLK pulses are added. * @param SmoothCalibMinusPulsesValue: Select the value of CALM[8:0] bits. * This parameter can be one any value from 0 to 0x000001FF. * @note To deactivate the smooth calibration, the field SmoothCalibPlusPulses * must be equal to SMOOTHCALIB_PLUSPULSES_RESET and the field * SmoothCalibMinusPulsesValue mut be equal to 0. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef* hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmoothCalibMinusPulsesValue) { uint32_t tickstart = 0; /* Check the parameters */ assert_param(IS_RTC_SMOOTH_CALIB_PERIOD(SmoothCalibPeriod)); assert_param(IS_RTC_SMOOTH_CALIB_PLUS(SmoothCalibPlusPulses)); assert_param(IS_RTC_SMOOTH_CALIB_MINUS(SmoothCalibMinusPulsesValue)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* check if a calibration is pending*/ if((hrtc->Instance->ISR & RTC_ISR_RECALPF) != RESET) { tickstart = HAL_GetTick(); /* check if a calibration is pending*/ while((hrtc->Instance->ISR & RTC_ISR_RECALPF) != RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } } /* Configure the Smooth calibration settings */ hrtc->Instance->CALR = (uint32_t)((uint32_t)SmoothCalibPeriod | (uint32_t)SmoothCalibPlusPulses | (uint32_t)SmoothCalibMinusPulsesValue); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Configures the Synchronization Shift Control Settings. * @note When REFCKON is set, firmware must not write to Shift control register. * @param hrtc: RTC handle * @param ShiftAdd1S: Select to add or not 1 second to the time calendar. * This parameter can be one of the following values : * @arg RTC_SHIFTADD1S_SET: Add one second to the clock calendar. * @arg RTC_SHIFTADD1S_RESET: No effect. * @param ShiftSubFS: Select the number of Second Fractions to substitute. * This parameter can be one any value from 0 to 0x7FFF. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetSynchroShift(RTC_HandleTypeDef* hrtc, uint32_t ShiftAdd1S, uint32_t ShiftSubFS) { uint32_t tickstart = 0; /* Check the parameters */ assert_param(IS_RTC_SHIFT_ADD1S(ShiftAdd1S)); assert_param(IS_RTC_SHIFT_SUBFS(ShiftSubFS)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); tickstart = HAL_GetTick(); /* Wait until the shift is completed*/ while((hrtc->Instance->ISR & RTC_ISR_SHPF) != RESET) { if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_TIMEOUT; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_TIMEOUT; } } /* Check if the reference clock detection is disabled */ if((hrtc->Instance->CR & RTC_CR_REFCKON) == RESET) { /* Configure the Shift settings */ hrtc->Instance->SHIFTR = (uint32_t)(uint32_t)(ShiftSubFS) | (uint32_t)(ShiftAdd1S); /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == RESET) { if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } } } else { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Configures the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). * @param hrtc: RTC handle * @param CalibOutput : Select the Calibration output Selection . * This parameter can be one of the following values: * @arg RTC_CALIBOUTPUT_512HZ: A signal has a regular waveform at 512Hz. * @arg RTC_CALIBOUTPUT_1HZ: A signal has a regular waveform at 1Hz. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetCalibrationOutPut(RTC_HandleTypeDef* hrtc, uint32_t CalibOutput) { /* Check the parameters */ assert_param(IS_RTC_CALIB_OUTPUT(CalibOutput)); /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Clear flags before config */ hrtc->Instance->CR &= (uint32_t)~RTC_CR_COSEL; /* Configure the RTC_CR register */ hrtc->Instance->CR |= (uint32_t)CalibOutput; __HAL_RTC_CALIBRATION_OUTPUT_ENABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Deactivates the Calibration Pinout (RTC_CALIB) Selection (1Hz or 512Hz). * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateCalibrationOutPut(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); __HAL_RTC_CALIBRATION_OUTPUT_DISABLE(hrtc); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Enables the RTC reference clock detection. * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_SetRefClock(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set Initialization mode */ if(RTC_EnterInitMode(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state*/ hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } else { __HAL_RTC_CLOCKREF_DETECTION_ENABLE(hrtc); /* Exit Initialization mode */ hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Disable the RTC reference clock detection. * @param hrtc: RTC handle * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DeactivateRefClock(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set Initialization mode */ if(RTC_EnterInitMode(hrtc) != HAL_OK) { /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Set RTC state*/ hrtc->State = HAL_RTC_STATE_ERROR; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_ERROR; } else { __HAL_RTC_CLOCKREF_DETECTION_DISABLE(hrtc); /* Exit Initialization mode */ hrtc->Instance->ISR &= (uint32_t)~RTC_ISR_INIT; } /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Enables the Bypass Shadow feature. * @param hrtc: RTC handle * @note When the Bypass Shadow is enabled the calendar value are taken * directly from the Calendar counter. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_EnableBypassShadow(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Set the BYPSHAD bit */ hrtc->Instance->CR |= (uint8_t)RTC_CR_BYPSHAD; /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @brief Disables the Bypass Shadow feature. * @param hrtc: RTC handle * @note When the Bypass Shadow is enabled the calendar value are taken * directly from the Calendar counter. * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_DisableBypassShadow(RTC_HandleTypeDef* hrtc) { /* Process Locked */ __HAL_LOCK(hrtc); hrtc->State = HAL_RTC_STATE_BUSY; /* Disable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc); /* Reset the BYPSHAD bit */ hrtc->Instance->CR &= ((uint8_t)~RTC_CR_BYPSHAD); /* Enable the write protection for RTC registers */ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; /* Process Unlocked */ __HAL_UNLOCK(hrtc); return HAL_OK; } /** * @} */ /** @addtogroup RTCEx_Exported_Functions_Group4 * @brief Extended features functions * @verbatim =============================================================================== ##### Extended features functions ##### =============================================================================== [..] This section provides functions allowing to: (+) RTC Alram B callback (+) RTC Poll for Alarm B request @endverbatim * @{ */ /** * @brief Alarm B callback. * @param hrtc: RTC handle * @retval None */ __weak void HAL_RTCEx_AlarmBEventCallback(RTC_HandleTypeDef *hrtc) { /* NOTE : This function Should not be modified, when the callback is needed, the HAL_RTC_AlarmBEventCallback could be implemented in the user file */ } /** * @brief This function handles AlarmB Polling request. * @param hrtc: RTC handle * @param Timeout: Timeout duration * @retval HAL status */ HAL_StatusTypeDef HAL_RTCEx_PollForAlarmBEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout) { uint32_t tickstart = HAL_GetTick(); while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBF) == RESET) { if(Timeout != HAL_MAX_DELAY) { if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) { hrtc->State = HAL_RTC_STATE_TIMEOUT; return HAL_TIMEOUT; } } } /* Clear the Alarm Flag */ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF); /* Change RTC state */ hrtc->State = HAL_RTC_STATE_READY; return HAL_OK; } /** * @} */ /** * @} */ #endif /* HAL_RTC_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/