X-Git-Url: https://git.gir.st/tmk_keyboard.git/blobdiff_plain/197ca829921a8b0bbdbf1a09c10f5bc2f6043eaa..b0573ba80e2a11724c7490ef5cdb528583178108:/converter/x68k_usb/Makefile diff --git a/converter/x68k_usb/Makefile b/converter/x68k_usb/Makefile index 19901bee..41e32b18 100644 --- a/converter/x68k_usb/Makefile +++ b/converter/x68k_usb/Makefile @@ -1,48 +1,45 @@ -# -# Makefile for PJRC Teensy -# - - # Target file name (without extension). -TARGET = x68k_usb +TARGET ?= x68k_usb # Directory common source filess exist -TMK_DIR = ../../tmk_core +TMK_DIR ?= ../../tmk_core # Directory keyboard dependent files exist -TARGET_DIR = . +TARGET_DIR ?= . -# keyboard dependent files -SRC = keymap.c \ - matrix.c \ +# project specific files +SRC ?= matrix.c \ led.c \ protocol/serial_uart.c CONFIG_H = config.h -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -#MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 -MCU = atmega32u2 # Teensy 2.0 - +# MCU name +# atmega32u4 Teensy2.0 +# atemga32u4 TMK Converter rev.1 +# atemga32u2 TMK Converter rev.2 +MCU ?= atmega32u2 # Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU ?= 16000000 # # LUFA specific # # Target architecture (see library "Board Types" documentation). -ARCH = AVR8 +ARCH ?= AVR8 # Input clock frequency. # This will define a symbol, F_USB, in all source code files equal to the @@ -55,69 +52,58 @@ ARCH = AVR8 # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) +F_USB ?= $(F_CPU) # Interrupt driven control endpoint task(+60) -#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT -# Boot Section Size in bytes +# Boot Section Size in *bytes* # Teensy halfKay 512 -# Atmel DFU loader 4096 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2 # LUFA bootloader 4096 +# USBaspLoader 2048 OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options -# *Comment out* to disable the options. +# comment out to disable the options. # -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = yes # Console for debug(+400) COMMAND_ENABLE = yes # Commands for debug and configuration -#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover - - - -#---------------- Programming Options -------------------------- -AVRDUDE = avrdude -# Type: avrdude -c ? to get a full listing. -AVRDUDE_PROGRAMMER = avr109 -AVRDUDE_PORT = /dev/ttyACM0 -AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex -#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep +#UNIMAP_ENABLE = yes +#ACTIONMAP_ENABLE = yes # Use 16bit actionmap instead of 8bit keymap +#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor -# Uncomment the following if you want avrdude's erase cycle counter. -# Note that this counter needs to be initialized first using -Yn, -# see avrdude manual. -#AVRDUDE_ERASE_COUNTER = -y -# Uncomment the following if you do /not/ wish a verification to be -# performed after programming the device. -#AVRDUDE_NO_VERIFY = -V - -# Increase verbosity level. Please use this when submitting bug -# reports about avrdude. See -# to submit bug reports. -#AVRDUDE_VERBOSE = -v -v - -AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) -AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) -AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) - -PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) +# +# Keymap file +# +ifeq (yes,$(strip $(UNIMAP_ENABLE))) + KEYMAP_FILE = unimap +else + ifeq (yes,$(strip $(ACTIONMAP_ENABLE))) + KEYMAP_FILE = actionmap + else + KEYMAP_FILE = keymap + endif +endif +ifdef KEYMAP + SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) +else + SRC := $(KEYMAP_FILE).c $(SRC) +endif # Search Path VPATH += $(TARGET_DIR) VPATH += $(TMK_DIR) - -include $(TMK_DIR)/protocol.mk include $(TMK_DIR)/protocol/lufa.mk +include $(TMK_DIR)/protocol.mk include $(TMK_DIR)/common.mk include $(TMK_DIR)/rules.mk