X-Git-Url: https://git.gir.st/tmk_keyboard.git/blobdiff_plain/afb08462085132acf7a1962522952f7dbf064519..8b509aa11140d4249824600aa9143fe1fca42d85:/converter/ps2_usb/Makefile

diff --git a/converter/ps2_usb/Makefile b/converter/ps2_usb/Makefile
index 0bba191a..5f9c4042 100644
--- a/converter/ps2_usb/Makefile
+++ b/converter/ps2_usb/Makefile
@@ -1,58 +1,116 @@
-#
-# Makefile for PJRC Teensy
-#
-
-
 # Target file name (without extension).
-TARGET = ps2_usb_pjrc
+TARGET ?= ps2_usb
 
 # Directory common source filess exist
-TOP_DIR = ../..
+TMK_DIR ?= ../../tmk_core
 
 # Directory keyboard dependent files exist
-TARGET_DIR = .
+TARGET_DIR ?= .
 
-# keyboard dependent files
-SRC =	main.c \
-	keymap.c \
-	matrix.c \
-	led.c \
-	ps2.c
+# project specific files
+SRC ?=	matrix.c \
+	led.c
 
-CONFIG_H = config_pjrc.h
+#
+# Keymap file
+#
+ifdef UNIMAP_ENABLE
+    KEYMAP_FILE = unimap
+else
+    ifdef ACTIONMAP_ENABLE
+	KEYMAP_FILE = actionmap
+    else
+	KEYMAP_FILE = keymap
+    endif
+endif
+ifdef KEYMAP
+    SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
+else
+    SRC := $(KEYMAP_FILE)_plain.c $(SRC)
+endif
+
+CONFIG_H ?= config.h
+
+
+# MCU name
+MCU ?= atmega32u2
 
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU ?= 16000000
 
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
 
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH ?= AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB ?= $(F_CPU)
 
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
+# Interrupt driven control endpoint task
+# Not work with suart debug
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# This improves response of keyboard when wakeup
+OPT_DEFS += -DSUSPEND_MODE_STANDBY
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+BOOTLOADER_SIZE ?= 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
 
 
 # Build Options
-#   *Comment out* to disable the options.
+#   comment out to disable the options.
 #
-MOUSEKEY_ENABLE = yes	# Mouse keys
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-NKRO_ENABLE = yes	# USB Nkey Rollover
+BOOTMAGIC_ENABLE ?= no	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= no	# Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes	# Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes	# Console for debug(+400)
+COMMAND_ENABLE ?= yes    # Commands for debug and configuration
+NKRO_ENABLE ?= yes	# USB Nkey Rollover
 
 
+# PS/2 Options
+#
+#PS2_USE_USART ?= yes	# uses hardware USART engine for PS/2 signal receive(recomened)
+PS2_USE_INT ?= yes	# uses external interrupt for falling edge of PS/2 clock pin
+#PS2_USE_BUSYWAIT ?= yes	# uses primitive reference code
 
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
 
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
 
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
 
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk