]>
Commit | Line | Data |
---|---|---|
1 | # | |
2 | # Makefile for TMK keyboard converter rev2 | |
3 | # https://github.com/tmk/keyboard_converter#pcb-rev1 | |
4 | # | |
5 | # Target file name (without extension). | |
6 | TARGET = ps2_usb_tmk_rev1 | |
7 | ||
8 | # Directory common source filess exist | |
9 | TMK_DIR = ../../tmk_core | |
10 | ||
11 | # Directory keyboard dependent files exist | |
12 | TARGET_DIR = . | |
13 | ||
14 | # project specific files | |
15 | SRC = matrix.c \ | |
16 | led.c | |
17 | ||
18 | ifdef KEYMAP | |
19 | SRC := keymap_$(KEYMAP).c $(SRC) | |
20 | else | |
21 | SRC := keymap_plain.c $(SRC) | |
22 | endif | |
23 | ||
24 | CONFIG_H = config_tmk_rev1.h | |
25 | ||
26 | ||
27 | # MCU name | |
28 | MCU = atmega32u4 | |
29 | ||
30 | # Processor frequency. | |
31 | # This will define a symbol, F_CPU, in all source code files equal to the | |
32 | # processor frequency in Hz. You can then use this symbol in your source code to | |
33 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
34 | # automatically to create a 32-bit value in your source code. | |
35 | # | |
36 | # This will be an integer division of F_USB below, as it is sourced by | |
37 | # F_USB after it has run through any CPU prescalers. Note that this value | |
38 | # does not *change* the processor frequency - it should merely be updated to | |
39 | # reflect the processor speed set externally so that the code can use accurate | |
40 | # software delays. | |
41 | F_CPU = 16000000 | |
42 | ||
43 | ||
44 | # | |
45 | # LUFA specific | |
46 | # | |
47 | # Target architecture (see library "Board Types" documentation). | |
48 | ARCH = AVR8 | |
49 | ||
50 | # Input clock frequency. | |
51 | # This will define a symbol, F_USB, in all source code files equal to the | |
52 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
53 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
54 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
55 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
56 | # at the end, this will be done automatically to create a 32-bit value in your | |
57 | # source code. | |
58 | # | |
59 | # If no clock division is performed on the input clock inside the AVR (via the | |
60 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
61 | F_USB = $(F_CPU) | |
62 | ||
63 | ||
64 | # Boot Section Size in *bytes* | |
65 | # Teensy halfKay 512 | |
66 | # Teensy++ halfKay 1024 | |
67 | # Atmel DFU loader 4096 | |
68 | # LUFA bootloader 4096 | |
69 | # USBaspLoader 2048 | |
70 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
71 | ||
72 | ||
73 | # Build Options | |
74 | # comment out to disable the options. | |
75 | # | |
76 | #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |
77 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
78 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
79 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
80 | COMMAND_ENABLE = yes # Commands for debug and configuration | |
81 | #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |
82 | ||
83 | ||
84 | # PS/2 Options | |
85 | # | |
86 | PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |
87 | #PS2_USE_BUSYWAIT = yes # uses primitive reference code | |
88 | ||
89 | ||
90 | # Search Path | |
91 | VPATH += $(TARGET_DIR) | |
92 | VPATH += $(TMK_DIR) | |
93 | ||
94 | include $(TMK_DIR)/protocol.mk | |
95 | include $(TMK_DIR)/protocol/lufa.mk | |
96 | include $(TMK_DIR)/common.mk | |
97 | include $(TMK_DIR)/rules.mk |