]>
Commit | Line | Data |
---|---|---|
1 | #---------------------------------------------------------------------------- | |
2 | # On command line: | |
3 | # | |
4 | # make all = Make software. | |
5 | # | |
6 | # make clean = Clean out built project files. | |
7 | # | |
8 | # make coff = Convert ELF to AVR COFF. | |
9 | # | |
10 | # make extcoff = Convert ELF to AVR Extended COFF. | |
11 | # | |
12 | # make program = Download the hex file to the device. | |
13 | # Please customize your programmer settings(PROGRAM_CMD) | |
14 | # | |
15 | # make teensy = Download the hex file to the device, using teensy_loader_cli. | |
16 | # (must have teensy_loader_cli installed). | |
17 | # | |
18 | # make dfu = Download the hex file to the device, using dfu-programmer (must | |
19 | # have dfu-programmer installed). | |
20 | # | |
21 | # make flip = Download the hex file to the device, using Atmel FLIP (must | |
22 | # have Atmel FLIP installed). | |
23 | # | |
24 | # make dfu-ee = Download the eeprom file to the device, using dfu-programmer | |
25 | # (must have dfu-programmer installed). | |
26 | # | |
27 | # make flip-ee = Download the eeprom file to the device, using Atmel FLIP | |
28 | # (must have Atmel FLIP installed). | |
29 | # | |
30 | # make debug = Start either simulavr or avarice as specified for debugging, | |
31 | # with avr-gdb or avr-insight as the front end for debugging. | |
32 | # | |
33 | # make filename.s = Just compile filename.c into the assembler code only. | |
34 | # | |
35 | # make filename.i = Create a preprocessed source file for use in submitting | |
36 | # bug reports to the GCC project. | |
37 | # | |
38 | # To rebuild project do "make clean" then "make all". | |
39 | #---------------------------------------------------------------------------- | |
40 | ||
41 | # Target file name (without extension). | |
42 | TARGET = gh60_lufa | |
43 | ||
44 | # Directory common source filess exist | |
45 | TMK_DIR = ../../tmk_core | |
46 | ||
47 | # Directory keyboard dependent files exist | |
48 | TARGET_DIR = . | |
49 | ||
50 | # project specific files | |
51 | SRC = matrix.c \ | |
52 | led.c | |
53 | ||
54 | ifdef KEYMAP | |
55 | SRC := keymap_$(KEYMAP).c $(SRC) | |
56 | else | |
57 | SRC := keymap_poker.c $(SRC) | |
58 | endif | |
59 | ||
60 | CONFIG_H = config.h | |
61 | ||
62 | ||
63 | # MCU name | |
64 | #MCU = at90usb1287 | |
65 | MCU = atmega32u4 | |
66 | ||
67 | # Processor frequency. | |
68 | # This will define a symbol, F_CPU, in all source code files equal to the | |
69 | # processor frequency in Hz. You can then use this symbol in your source code to | |
70 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
71 | # automatically to create a 32-bit value in your source code. | |
72 | # | |
73 | # This will be an integer division of F_USB below, as it is sourced by | |
74 | # F_USB after it has run through any CPU prescalers. Note that this value | |
75 | # does not *change* the processor frequency - it should merely be updated to | |
76 | # reflect the processor speed set externally so that the code can use accurate | |
77 | # software delays. | |
78 | F_CPU = 16000000 | |
79 | ||
80 | ||
81 | # | |
82 | # LUFA specific | |
83 | # | |
84 | # Target architecture (see library "Board Types" documentation). | |
85 | ARCH = AVR8 | |
86 | ||
87 | # Input clock frequency. | |
88 | # This will define a symbol, F_USB, in all source code files equal to the | |
89 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
90 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
91 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
92 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
93 | # at the end, this will be done automatically to create a 32-bit value in your | |
94 | # source code. | |
95 | # | |
96 | # If no clock division is performed on the input clock inside the AVR (via the | |
97 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
98 | F_USB = $(F_CPU) | |
99 | ||
100 | # Interrupt driven control endpoint task(+60) | |
101 | OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
102 | ||
103 | ||
104 | # Boot Section Size in *bytes* | |
105 | # Teensy halfKay 512 | |
106 | # Teensy++ halfKay 1024 | |
107 | # Atmel DFU loader 4096 | |
108 | # LUFA bootloader 4096 | |
109 | # USBaspLoader 2048 | |
110 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
111 | ||
112 | ||
113 | # Build Options | |
114 | # comment out to disable the options. | |
115 | # | |
116 | BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |
117 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
118 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
119 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
120 | COMMAND_ENABLE = yes # Commands for debug and configuration | |
121 | #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |
122 | NKRO_ENABLE = yes # USB Nkey Rollover | |
123 | ||
124 | ||
125 | # Optimize size but this may cause error "relocation truncated to fit" | |
126 | #EXTRALDFLAGS = -Wl,--relax | |
127 | ||
128 | # Search Path | |
129 | VPATH += $(TARGET_DIR) | |
130 | VPATH += $(TMK_DIR) | |
131 | ||
132 | include $(TMK_DIR)/protocol/lufa.mk | |
133 | include $(TMK_DIR)/common.mk | |
134 | include $(TMK_DIR)/rules.mk |