6fc29cbf065c0743c4ef0ca5492fde909c572056
[tmk_keyboard.git] / converter / xt_usb / Makefile
1 #
2 # Makefile for Teensy
3 #
4 # Target file name (without extension).
5 TARGET = xt_usb_lufa
6
7 # Directory common source filess exist
8 TMK_DIR = ../../tmk_core
9
10 # Directory keyboard dependent files exist
11 TARGET_DIR = .
12
13 # project specific files
14 SRC = matrix.c \
15 led.c
16
17 ifdef KEYMAP
18 SRC := keymap_$(KEYMAP).c $(SRC)
19 else
20 SRC := keymap_plain.c $(SRC)
21 endif
22
23 CONFIG_H = config.h
24
25
26 # MCU name
27 #MCU = at90usb1287
28 MCU = atmega32u4
29
30 # Processor frequency.
31 # This will define a symbol, F_CPU, in all source code files equal to the
32 # processor frequency in Hz. You can then use this symbol in your source code to
33 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
34 # automatically to create a 32-bit value in your source code.
35 #
36 # This will be an integer division of F_USB below, as it is sourced by
37 # F_USB after it has run through any CPU prescalers. Note that this value
38 # does not *change* the processor frequency - it should merely be updated to
39 # reflect the processor speed set externally so that the code can use accurate
40 # software delays.
41 F_CPU = 16000000
42
43
44 #
45 # LUFA specific
46 #
47 # Target architecture (see library "Board Types" documentation).
48 ARCH = AVR8
49
50 # Input clock frequency.
51 # This will define a symbol, F_USB, in all source code files equal to the
52 # input clock frequency (before any prescaling is performed) in Hz. This value may
53 # differ from F_CPU if prescaling is used on the latter, and is required as the
54 # raw input clock is fed directly to the PLL sections of the AVR for high speed
55 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
56 # at the end, this will be done automatically to create a 32-bit value in your
57 # source code.
58 #
59 # If no clock division is performed on the input clock inside the AVR (via the
60 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
61 F_USB = $(F_CPU)
62
63 # Interrupt driven control endpoint task(+60)
64 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
65
66
67 # Boot Section Size in *bytes*
68 # Teensy halfKay 512
69 # Teensy++ halfKay 1024
70 # Atmel DFU loader 4096
71 # LUFA bootloader 4096
72 # USBaspLoader 2048
73 OPT_DEFS += -DBOOTLOADER_SIZE=512
74
75
76 # Build Options
77 # comment out to disable the options.
78 #
79 #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
80 MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
81 EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
82 CONSOLE_ENABLE = yes # Console for debug(+400)
83 COMMAND_ENABLE = yes # Commands for debug and configuration
84 NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
85
86
87 # XT/2 Options
88 #
89 XT_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
90
91
92 # Optimize size but this may cause error "relocation truncated to fit"
93 #EXTRALDFLAGS = -Wl,--relax
94
95 # Search Path
96 VPATH += $(TARGET_DIR)
97 VPATH += $(TMK_DIR)
98
99 include $(TMK_DIR)/protocol.mk
100 include $(TMK_DIR)/protocol/lufa.mk
101 include $(TMK_DIR)/common.mk
102 include $(TMK_DIR)/rules.mk
Imprint / Impressum