]>
Commit | Line | Data |
---|---|---|
1 | # | |
2 | # Makefile for PJRC Teensy | |
3 | # | |
4 | ||
5 | ||
6 | # Target file name (without extension). | |
7 | TARGET = x68k_usb | |
8 | ||
9 | # Directory common source filess exist | |
10 | TMK_DIR = ../../tmk_core | |
11 | ||
12 | # Directory keyboard dependent files exist | |
13 | TARGET_DIR = . | |
14 | ||
15 | # keyboard dependent files | |
16 | SRC = keymap.c \ | |
17 | matrix.c \ | |
18 | led.c \ | |
19 | protocol/serial_uart.c | |
20 | ||
21 | CONFIG_H = config.h | |
22 | ||
23 | ||
24 | # MCU name, you MUST set this to match the board you are using | |
25 | # type "make clean" after changing this, so all files will be rebuilt | |
26 | #MCU = at90usb162 # Teensy 1.0 | |
27 | #MCU = atmega32u4 # Teensy 2.0 | |
28 | #MCU = at90usb646 # Teensy++ 1.0 | |
29 | #MCU = at90usb1286 # Teensy++ 2.0 | |
30 | MCU = atmega32u2 # Teensy 2.0 | |
31 | ||
32 | ||
33 | # Processor frequency. | |
34 | # Normally the first thing your program should do is set the clock prescaler, | |
35 | # so your program will run at the correct speed. You should also set this | |
36 | # variable to same clock speed. The _delay_ms() macro uses this, and many | |
37 | # examples use this variable to calculate timings. Do not add a "UL" here. | |
38 | F_CPU = 16000000 | |
39 | ||
40 | ||
41 | # | |
42 | # LUFA specific | |
43 | # | |
44 | # Target architecture (see library "Board Types" documentation). | |
45 | ARCH = AVR8 | |
46 | ||
47 | # Input clock frequency. | |
48 | # This will define a symbol, F_USB, in all source code files equal to the | |
49 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
50 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
51 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
52 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
53 | # at the end, this will be done automatically to create a 32-bit value in your | |
54 | # source code. | |
55 | # | |
56 | # If no clock division is performed on the input clock inside the AVR (via the | |
57 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
58 | F_USB = $(F_CPU) | |
59 | ||
60 | # Interrupt driven control endpoint task(+60) | |
61 | #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
62 | ||
63 | ||
64 | # Boot Section Size in bytes | |
65 | # Teensy halfKay 512 | |
66 | # Atmel DFU loader 4096 | |
67 | # LUFA bootloader 4096 | |
68 | OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |
69 | ||
70 | ||
71 | # Build Options | |
72 | # *Comment out* to disable the options. | |
73 | # | |
74 | BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |
75 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
76 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
77 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
78 | COMMAND_ENABLE = yes # Commands for debug and configuration | |
79 | #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |
80 | #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |
81 | ||
82 | ||
83 | ||
84 | #---------------- Programming Options -------------------------- | |
85 | AVRDUDE = avrdude | |
86 | # Type: avrdude -c ? to get a full listing. | |
87 | AVRDUDE_PROGRAMMER = avr109 | |
88 | AVRDUDE_PORT = /dev/ttyACM0 | |
89 | AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex | |
90 | #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep | |
91 | ||
92 | # Uncomment the following if you want avrdude's erase cycle counter. | |
93 | # Note that this counter needs to be initialized first using -Yn, | |
94 | # see avrdude manual. | |
95 | #AVRDUDE_ERASE_COUNTER = -y | |
96 | ||
97 | # Uncomment the following if you do /not/ wish a verification to be | |
98 | # performed after programming the device. | |
99 | #AVRDUDE_NO_VERIFY = -V | |
100 | ||
101 | # Increase verbosity level. Please use this when submitting bug | |
102 | # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> | |
103 | # to submit bug reports. | |
104 | #AVRDUDE_VERBOSE = -v -v | |
105 | ||
106 | AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) | |
107 | #AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) | |
108 | AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) | |
109 | AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) | |
110 | AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) | |
111 | ||
112 | PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) | |
113 | ||
114 | ||
115 | # Search Path | |
116 | VPATH += $(TARGET_DIR) | |
117 | VPATH += $(TMK_DIR) | |
118 | ||
119 | ||
120 | include $(TMK_DIR)/protocol.mk | |
121 | include $(TMK_DIR)/protocol/lufa.mk | |
122 | include $(TMK_DIR)/common.mk | |
123 | include $(TMK_DIR)/rules.mk |