]>
Commit | Line | Data |
---|---|---|
1 | # | |
2 | # Makefile for Teensy | |
3 | # | |
4 | # Target file name (without extension). | |
5 | TARGET = xt_usb_lufa | |
6 | ||
7 | # Directory common source filess exist | |
8 | TMK_DIR = ../../tmk_core | |
9 | ||
10 | # Directory keyboard dependent files exist | |
11 | TARGET_DIR = . | |
12 | ||
13 | # project specific files | |
14 | SRC = matrix.c \ | |
15 | led.c | |
16 | ||
17 | ifdef KEYMAP | |
18 | SRC := keymap_$(KEYMAP).c $(SRC) | |
19 | else | |
20 | SRC := keymap_plain.c $(SRC) | |
21 | endif | |
22 | ||
23 | CONFIG_H = config.h | |
24 | ||
25 | ||
26 | # MCU name | |
27 | #MCU = at90usb1287 | |
28 | MCU = atmega32u4 | |
29 | ||
30 | # Processor frequency. | |
31 | # This will define a symbol, F_CPU, in all source code files equal to the | |
32 | # processor frequency in Hz. You can then use this symbol in your source code to | |
33 | # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |
34 | # automatically to create a 32-bit value in your source code. | |
35 | # | |
36 | # This will be an integer division of F_USB below, as it is sourced by | |
37 | # F_USB after it has run through any CPU prescalers. Note that this value | |
38 | # does not *change* the processor frequency - it should merely be updated to | |
39 | # reflect the processor speed set externally so that the code can use accurate | |
40 | # software delays. | |
41 | F_CPU = 16000000 | |
42 | ||
43 | ||
44 | # | |
45 | # LUFA specific | |
46 | # | |
47 | # Target architecture (see library "Board Types" documentation). | |
48 | ARCH = AVR8 | |
49 | ||
50 | # Input clock frequency. | |
51 | # This will define a symbol, F_USB, in all source code files equal to the | |
52 | # input clock frequency (before any prescaling is performed) in Hz. This value may | |
53 | # differ from F_CPU if prescaling is used on the latter, and is required as the | |
54 | # raw input clock is fed directly to the PLL sections of the AVR for high speed | |
55 | # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |
56 | # at the end, this will be done automatically to create a 32-bit value in your | |
57 | # source code. | |
58 | # | |
59 | # If no clock division is performed on the input clock inside the AVR (via the | |
60 | # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |
61 | F_USB = $(F_CPU) | |
62 | ||
63 | # Interrupt driven control endpoint task(+60) | |
64 | #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |
65 | ||
66 | ||
67 | # Boot Section Size in *bytes* | |
68 | # Teensy halfKay 512 | |
69 | # Teensy++ halfKay 1024 | |
70 | # Atmel DFU loader 4096 | |
71 | # LUFA bootloader 4096 | |
72 | # USBaspLoader 2048 | |
73 | OPT_DEFS += -DBOOTLOADER_SIZE=512 | |
74 | ||
75 | ||
76 | # Build Options | |
77 | # comment out to disable the options. | |
78 | # | |
79 | #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |
80 | MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |
81 | EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |
82 | CONSOLE_ENABLE = yes # Console for debug(+400) | |
83 | COMMAND_ENABLE = yes # Commands for debug and configuration | |
84 | NKRO_ENABLE = yes # USB Nkey Rollover | |
85 | ||
86 | ||
87 | # XT/2 Options | |
88 | # | |
89 | XT_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |
90 | ||
91 | ||
92 | # Optimize size but this may cause error "relocation truncated to fit" | |
93 | #EXTRALDFLAGS = -Wl,--relax | |
94 | ||
95 | # Search Path | |
96 | VPATH += $(TARGET_DIR) | |
97 | VPATH += $(TMK_DIR) | |
98 | ||
99 | include $(TMK_DIR)/protocol.mk | |
100 | include $(TMK_DIR)/protocol/lufa.mk | |
101 | include $(TMK_DIR)/common.mk | |
102 | include $(TMK_DIR)/rules.mk |