]>
git.gir.st - tmk_keyboard.git/blob - keyboard/hhkb/Makefile
1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
44 # Directory common source filess exist
47 # Directory keyboard dependent files exist
51 # List C source files here. (C dependencies are automatically generated.)
52 SRC
+= keymap_common.c \
57 SRC
:= keymap_
$(KEYMAP
).c
$(SRC
)
59 SRC
:= keymap_hasu.c
$(SRC
)
68 # TMK Alt Controller or PJRC Teensy 2.0
71 # Processor frequency.
72 # This will define a symbol, F_CPU, in all source code files equal to the
73 # processor frequency in Hz. You can then use this symbol in your source code to
74 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
75 # automatically to create a 32-bit value in your source code.
77 # This will be an integer division of F_USB below, as it is sourced by
78 # F_USB after it has run through any CPU prescalers. Note that this value
79 # does not *change* the processor frequency - it should merely be updated to
80 # reflect the processor speed set externally so that the code can use accurate
88 # Target architecture (see library "Board Types" documentation).
91 # Input clock frequency.
92 # This will define a symbol, F_USB, in all source code files equal to the
93 # input clock frequency (before any prescaling is performed) in Hz. This value may
94 # differ from F_CPU if prescaling is used on the latter, and is required as the
95 # raw input clock is fed directly to the PLL sections of the AVR for high speed
96 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
97 # at the end, this will be done automatically to create a 32-bit value in your
100 # If no clock division is performed on the input clock inside the AVR (via the
101 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
104 # Interrupt driven control endpoint task
105 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
108 # Boot Section Size in *bytes*
110 # Teensy++ halfKay 1024
111 # Atmel DFU loader 4096 (TMK Alt Controller)
112 # LUFA bootloader 4096
114 OPT_DEFS
+= -DBOOTLOADER_SIZE
=4096
118 # comment out to disable the options.
120 BOOTMAGIC_ENABLE
= yes
# Virtual DIP switch configuration
121 MOUSEKEY_ENABLE
= yes
# Mouse keys
122 EXTRAKEY_ENABLE
= yes
# Audio control and System control
123 CONSOLE_ENABLE
= yes
# Console for debug
124 COMMAND_ENABLE
= yes
# Commands for debug and configuration
125 NKRO_ENABLE
= yes
# USB Nkey Rollover
126 KEYMAP_SECTION_ENABLE
= yes
# fixed address keymap for keymap editor
130 VPATH
+= $(TARGET_DIR
)
133 include $(TOP_DIR
)/protocol
/lufa.mk
134 include $(TOP_DIR
)/common.mk
135 include $(TOP_DIR
)/rules.mk
137 debug-on
: EXTRAFLAGS
+= -DDEBUG
-DDEBUG_ACTION
140 debug-off
: EXTRAFLAGS
+= -DNO_DEBUG
-DNO_PRINT