1 #----------------------------------------------------------------------------
4 # make all = Make software.
6 # make clean = Clean out built project files.
8 # make coff = Convert ELF to AVR COFF.
10 # make extcoff = Convert ELF to AVR Extended COFF.
12 # make program = Download the hex file to the device.
13 # Please customize your programmer settings(PROGRAM_CMD)
15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
16 # (must have teensy_loader_cli installed).
18 # make dfu = Download the hex file to the device, using dfu-programmer (must
19 # have dfu-programmer installed).
21 # make flip = Download the hex file to the device, using Atmel FLIP (must
22 # have Atmel FLIP installed).
24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
25 # (must have dfu-programmer installed).
27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
28 # (must have Atmel FLIP installed).
30 # make debug = Start either simulavr or avarice as specified for debugging,
31 # with avr-gdb or avr-insight as the front end for debugging.
33 # make filename.s = Just compile filename.c into the assembler code only.
35 # make filename.i = Create a preprocessed source file for use in submitting
36 # bug reports to the GCC project.
38 # To rebuild project do "make clean" then "make all".
39 #----------------------------------------------------------------------------
41 # Target file name (without extension).
43 TARGET
= $(TARGETFILE
)
48 # Directory common source filess exist
49 TMK_DIR
= ..
/..
/tmk_core
51 # Directory keyboard dependent files exist
54 # project specific files
61 SRC
:= keymap_
$(KEYMAP
).c
$(SRC
)
63 SRC
:= keymap_blazak.c
$(SRC
)
69 # MCU name, you MUST set this to match the board you are using
70 # type "make clean" after changing this, so all files will be rebuilt
75 # Processor frequency.
76 # Normally the first thing your program should do is set the clock prescaler,
77 # so your program will run at the correct speed. You should also set this
78 # variable to same clock speed. The _delay_ms() macro uses this, and many
79 # examples use this variable to calculate timings. Do not add a "UL" here.
86 # Target architecture (see library "Board Types" documentation).
89 # Input clock frequency.
90 # This will define a symbol, F_USB, in all source code files equal to the
91 # input clock frequency (before any prescaling is performed) in Hz. This value may
92 # differ from F_CPU if prescaling is used on the latter, and is required as the
93 # raw input clock is fed directly to the PLL sections of the AVR for high speed
94 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
95 # at the end, this will be done automatically to create a 32-bit value in your
98 # If no clock division is performed on the input clock inside the AVR (via the
99 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
102 # Interrupt driven control endpoint task
103 OPT_DEFS
+= -DINTERRUPT_CONTROL_ENDPOINT
105 # Boot Section Size in *bytes*
107 # Atmel DFU loader 4096
108 # LUFA bootloader 4096
109 OPT_DEFS
+= -DBOOTLOADER_SIZE
=512
112 # comment out to disable the options.
114 BOOTMAGIC_ENABLE
= yes
# Virtual DIP switch configuration(+1000)
115 MOUSEKEY_ENABLE
= yes
# Mouse keys(+5000)
116 EXTRAKEY_ENABLE
= yes
# Audio control and System control(+600)
117 CONSOLE_ENABLE
= yes
# Console for debug
118 COMMAND_ENABLE
= yes
# Commands for debug and configuration
119 SLEEP_LED_ENABLE
= yes
# Breathing sleep LED during USB suspend
120 NKRO_ENABLE
= yes
# USB Nkey Rollover (+500)
121 #PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support
122 INVERT_NUMLOCK
= yes
# invert state of NumLock led
126 VPATH
+= $(TARGET_DIR
)
129 include $(TMK_DIR
)/protocol.mk
130 include $(TMK_DIR
)/protocol
/lufa.mk
131 include $(TMK_DIR
)/common.mk
132 include $(TMK_DIR
)/rules.mk