keyboard/ergodox/Makefile

   1 #----------------------------------------------------------------------------
   2 # On command line:
   3 #
   4 # make all = Make software.
   5 #
   6 # make clean = Clean out built project files.
   7 #
   8 # make coff = Convert ELF to AVR COFF.
   9 #
  10 # make extcoff = Convert ELF to AVR Extended COFF.
  11 #
  12 # make program = Download the hex file to the device.
  13 #                Please customize your programmer settings(PROGRAM_CMD)
  14 #
  15 # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16 #               (must have teensy_loader_cli installed).
  17 #
  18 # make dfu = Download the hex file to the device, using dfu-programmer (must
  19 #            have dfu-programmer installed).
  20 #
  21 # make flip = Download the hex file to the device, using Atmel FLIP (must
  22 #             have Atmel FLIP installed).
  23 #
  24 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25 #               (must have dfu-programmer installed).
  26 #
  27 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28 #                (must have Atmel FLIP installed).
  29 #
  30 # make debug = Start either simulavr or avarice as specified for debugging,
  31 #              with avr-gdb or avr-insight as the front end for debugging.
  32 #
  33 # make filename.s = Just compile filename.c into the assembler code only.
  34 #
  35 # make filename.i = Create a preprocessed source file for use in submitting
  36 #                   bug reports to the GCC project.
  37 #
  38 # To rebuild project do "make clean" then "make all".
  39 #----------------------------------------------------------------------------
  40
  41 # Target file name (without extension).
  42 ifdef TARGETFILE
  43         TARGET = $(TARGETFILE)
  44 else
  45         TARGET = ergodox_lufa
  46 endif
  47
  48 # Directory common source filess exist
  49 TMK_DIR = ../../tmk_core
  50
  51 # Directory keyboard dependent files exist
  52 TARGET_DIR = .
  53
  54 # project specific files
  55 SRC =   matrix.c \
  56         led.c \
  57         ergodox.c \
  58         twimaster.c
  59
  60 ifdef KEYMAP
  61     SRC := keymap_$(KEYMAP).c $(SRC)
  62 else
  63     SRC := keymap_blazak.c $(SRC)
  64 endif
  65
  66 CONFIG_H = config.h
  67
  68
  69 # MCU name, you MUST set this to match the board you are using
  70 # type "make clean" after changing this, so all files will be rebuilt
  71 MCU = atmega32u4
  72 #MCU = at90usb1286
  73
  74
  75 # Processor frequency.
  76 #   Normally the first thing your program should do is set the clock prescaler,
  77 #   so your program will run at the correct speed.  You should also set this
  78 #   variable to same clock speed.  The _delay_ms() macro uses this, and many
  79 #   examples use this variable to calculate timings.  Do not add a "UL" here.
  80 F_CPU = 16000000
  81
  82
  83 #
  84 # LUFA specific
  85 #
  86 # Target architecture (see library "Board Types" documentation).
  87 ARCH = AVR8
  88
  89 # Input clock frequency.
  90 #     This will define a symbol, F_USB, in all source code files equal to the
  91 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  92 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  93 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  94 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  95 #     at the end, this will be done automatically to create a 32-bit value in your
  96 #     source code.
  97 #
  98 #     If no clock division is performed on the input clock inside the AVR (via the
  99 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 100 F_USB = $(F_CPU)
 101
 102 # Interrupt driven control endpoint task
 103 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 104
 105 # Boot Section Size in *bytes*
 106 #   Teensy halfKay   512
 107 #   Atmel DFU loader 4096
 108 #   LUFA bootloader  4096
 109 OPT_DEFS += -DBOOTLOADER_SIZE=512
 110
 111 # Build Options
 112 #   comment out to disable the options.
 113 #
 114 BOOTMAGIC_ENABLE = yes  # Virtual DIP switch configuration(+1000)
 115 MOUSEKEY_ENABLE = yes   # Mouse keys(+5000)
 116 EXTRAKEY_ENABLE = yes   # Audio control and System control(+600)
 117 CONSOLE_ENABLE = yes    # Console for debug
 118 COMMAND_ENABLE = yes    # Commands for debug and configuration
 119 SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
 120 NKRO_ENABLE = yes               # USB Nkey Rollover (+500)
 121 #PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support
 122 INVERT_NUMLOCK = yes    # invert state of NumLock led
 123
 124
 125 # Search Path
 126 VPATH += $(TARGET_DIR)
 127 VPATH += $(TMK_DIR)
 128
 129 include $(TMK_DIR)/protocol.mk
 130 include $(TMK_DIR)/protocol/lufa.mk
 131 include $(TMK_DIR)/common.mk
 132 include $(TMK_DIR)/rules.mk